参数资料
型号: PIC18F4420T-I/ML
厂商: Microchip Technology
文件页数: 31/151页
文件大小: 0K
描述: IC MCU FLASH 8KX16 44QFN
产品培训模块: Asynchronous Stimulus
标准包装: 1,600
系列: PIC® 18F
核心处理器: PIC
芯体尺寸: 8-位
速度: 40MHz
连通性: I²C,SPI,UART/USART
外围设备: 欠压检测/复位,HLVD,POR,PWM,WDT
输入/输出数: 36
程序存储器容量: 16KB(8K x 16)
程序存储器类型: 闪存
EEPROM 大小: 256 x 8
RAM 容量: 768 x 8
电压 - 电源 (Vcc/Vdd): 4.2 V ~ 5.5 V
数据转换器: A/D 13x10b
振荡器型: 内部
工作温度: -40°C ~ 85°C
封装/外壳: 44-VQFN 裸露焊盘
包装: 带卷 (TR)
2011-2012 Microchip Technology Inc.
Preliminary
DS41579C-page 299
PIC16(L)F1782/3
26.6.5
I2
C MASTER MODE REPEATED
START CONDITION TIMING
A Repeated Start condition occurs when the RSEN bit
of the SSPCON2 register is programmed high and the
master state machine is no longer active. When the
RSEN bit is set, the SCL pin is asserted low. When the
SCL pin is sampled low, the Baud Rate Generator is
loaded and begins counting. The SDA pin is released
(brought high) for one Baud Rate Generator count
(TBRG). When the Baud Rate Generator times out, if
SDA is sampled high, the SCL pin will be deasserted
(brought high). When SCL is sampled high, the Baud
Rate Generator is reloaded and begins counting. SDA
and SCL must be sampled high for one TBRG. This
action is then followed by assertion of the SDA pin
(SDA = 0) for one TBRG while SCL is high. SCL is
asserted low. Following this, the RSEN bit of the
SSPCON2 register will be automatically cleared and
the Baud Rate Generator will not be reloaded, leaving
the SDA pin held low. As soon as a Start condition is
detected on the SDA and SCL pins, the S bit of the
SSPSTAT register will be set. The SSPIF bit will not be
set until the Baud Rate Generator has timed out.
FIGURE 26-27:
REPEAT START CONDITION WAVEFORM
Note 1:
If RSEN is programmed while any other
event is in progress, it will not take effect.
2:
A bus collision during the Repeated Start
condition occurs if:
SDA is sampled low when SCL
goes from low-to-high.
SCL goes low before SDA is
asserted low. This may indicate
that another master is attempting
to transmit a data ‘1’.
SDA
SCL
Repeated Start
Write to SSPCON2
Write to SSPBUF occurs here
At completion of Start bit,
hardware clears RSEN bit
1st bit
S bit set by hardware
TBRG
SDA = 1,
SCL (no change)
SCL = 1
occurs here
TBRG
and sets SSPIF
Sr
相关PDF资料
PDF描述
PIC16F88-E/SO IC MCU FLASH 4KX14 EEPROM 18SOIC
PIC16LF73T-I/SS IC MCU FLASH 4KX14 A/D 28SSOP
PI5V330QE IC VIDEO MUX/DEMUX 2X1 16QSOP
ISL84781IRZ IC MUX/DEMUX 8X1 16TQFN
VI-23M-CV-F2 CONVERTER MOD DC/DC 10V 150W
相关代理商/技术参数
参数描述
PIC18F4423-E/ML 功能描述:8位微控制器 -MCU 16KB 768bytes-RAM 36I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC18F4423-E/P 功能描述:8位微控制器 -MCU 16KB 768bytes-RAM 36I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC18F4423-E/PT 功能描述:8位微控制器 -MCU 16KB 768bytes-RAM 36I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC18F4423-I/ML 功能描述:8位微控制器 -MCU 16KB 768bytes-RAM 36I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC18F4423-I/P 功能描述:8位微控制器 -MCU 16KB 768bytes-RAM 36I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT