- 您现在的位置：买卖IC网 > PDF目录3855 > PIC18LF2321-I/ML (Microchip Technology)IC PIC MCU FLASH 4KX16 28QFN PDF资料下载
参数资料
| 型号： | PIC18LF2321-I/ML |
| 厂商： | Microchip Technology |
| 文件页数： | 41/110页 |
| 文件大小： | 0K |
| 描述： | IC PIC MCU FLASH 4KX16 28QFN |
| 产品培训模块： | Asynchronous Stimulus 8-bit PIC® Microcontroller Portfolio |
| 标准包装： | 61 |
| 系列： | PIC® 18F |
| 核心处理器： | PIC |
| 芯体尺寸： | 8-位 |
| 速度： | 40MHz |
| 连通性： | I²C，SPI，UART/USART |
| 外围设备： | 欠压检测/复位，HLVD，POR，PWM，WDT |
| 输入/输出数： | 25 |
| 程序存储器容量： | 8KB（4K x 16） |
| 程序存储器类型： | 闪存 |
| EEPROM 大小： | 256 x 8 |
| RAM 容量： | 512 x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 2 V ~ 5.5 V |
| 数据转换器： | A/D 10x10b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 28-VQFN 裸露焊盘 |
| 包装： | 管件 |
| 产品目录页面： | 642 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页当前第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页
PIC18F2221/2321/4221/4321 FAMILY
DS39689F-page 36
2009 Microchip Technology Inc.
3.7.1
OSCILLATOR CONTROL REGISTER
The OSCCON register (Register 3-2) controls several
aspects of the device clock’s operation, both in full
power operation and in power-managed modes.
The System Clock Select bits, SCS<1:0>, select the
clock source. The available clock sources are the
primary clock (defined by the FOSC<3:0> Configura-
tion bits), the secondary clock (Timer1 oscillator) and
the internal oscillator block. The clock source changes
immediately after either of the SCS<1:0> bits are
changed, following a brief clock transition interval. The
SCS bits are reset on all forms of Reset.
The
Internal
Oscillator
Frequency
Select
bits
(IRCF<2:0>) select the frequency output of the internal
oscillator block to drive the device clock. The choices
are the INTRC source (31 kHz), the INTOSC source
(8 MHz) or one of the frequencies derived from the
INTOSC postscaler (31.25 kHz to 4 MHz). If the
internal oscillator block is supplying the device clock,
changing the states of these bits will have an immedi-
ate change on the internal oscillator’s output. On
device Resets, the default output frequency of the
internal oscillator block is set at 1 MHz.
When a nominal output frequency of 31 kHz is selected
(IRCF<2:0> = 000), users may choose which internal
oscillator acts as the source. This is done with the
INTSRC bit in the OSCTUNE register (OSCTUNE<7>).
Setting this bit selects INTOSC as a 31.25 kHz clock
source derived from the INTOSC postscaler. Clearing
INTSRC selects INTRC (nominally 31 kHz) as the
clock source and disables the INTOSC to reduce
current consumption.
This option allows users to select the tunable and more
precise INTOSC as a clock source, while maintaining
power savings with a very low clock speed. Addition-
ally, the INTOSC source will already be stable should a
switch to a higher frequency be needed quickly.
Regardless of the setting of INTSRC, INTRC always
remains the clock source for features such as the
Watchdog Timer and the Fail-Safe Clock Monitor.
The OSTS, IOFS and T1RUN bits indicate which clock
source is currently providing the device clock. The
OSTS bit indicates that the Oscillator Start-up Timer
and PLL Start-up Timer (if enabled) have timed out and
the primary clock is providing the device clock in
primary clock modes. The IOFS bit indicates when the
internal oscillator block has stabilized and is providing
the device clock in RC Clock modes. The T1RUN bit
(T1CON<6>) indicates when the Timer1 oscillator is
providing the device clock in secondary clock modes.
In power-managed modes, only one of these three bits
will be set at any time. If none of these bits are set, the
INTRC is providing the clock or the internal oscillator
block has just started and is not yet stable.
The IDLEN bit controls whether the device goes into
Sleep mode or one of the Idle modes when the SLEEP
instruction is executed.
The use of the flag and control bits in the OSCCON
register is discussed in more detail in Section 4.0
3.7.2
OSCILLATOR TRANSITIONS
The PIC18F2221/2321/4221/4321 family of devices con-
tains circuitry to prevent clock “glitches” when switching
between clock sources. A short pause in the device clock
occurs during the clock switch. The length of this pause
is the sum of two cycles of the old clock source and three
to four cycles of the new clock source. This formula
assumes that the new clock source is stable.
Clock transitions are discussed in greater detail in
Note 1: The Timer1 oscillator must be enabled to
select the secondary clock source. The
Timer1 oscillator is enabled by setting the
T1OSCEN bit in the Timer1 Control regis-
ter (T1CON<3>). If the Timer1 oscillator
is not enabled, then any attempt to select
a secondary clock source will be ignored.
2: It is recommended that the Timer1
oscillator be operating and stable before
selecting the secondary clock source or a
very long delay may occur while the
Timer1 oscillator starts.
相关PDF资料 |
PDF描述 |
|---|---|
| PIC18F4321-I/P | IC PIC MCU FLASH 4KX16 40DIP |
| ATMEGA32L-8MC | IC AVR MCU 32K LV 8MHZ COM 44QFN |
| PIC18F2450-I/SP | IC PIC MCU FLASH 8KX16 28DIP |
| PIC24FJ64GA006-I/PT | IC PIC MCU FLASH 64KB 64TQFP |
| PIC18F26J53-I/SO | IC PIC MCU 64KB FLASH 28SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PIC18LF2321T-I/ML | 功能描述:8位微控制器 -MCU 8 KB FL 512 RAM RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| PIC18LF2321T-I/SO | 功能描述:8位微控制器 -MCU 8 KB FL 512 RAM RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| PIC18LF2321T-I/SS | 功能描述:8位微控制器 -MCU 8KB FLSH 512BRAM 8B nanoWatt RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| PIC18LF2331-I/ML | 功能描述:8位微控制器 -MCU 8KB 768 RAM 22I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| PIC18LF2331-I/MM | 功能描述:8位微控制器 -MCU 8 KB 768 RAM 22 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。