- 您现在的位置：买卖IC网 > PDF目录11745 > PIC24HJ64GP506A-I/PT (Microchip Technology)IC PIC MCU FLASH 64KB 64-TQFP PDF资料下载
参数资料
| 型号： | PIC24HJ64GP506A-I/PT |
| 厂商： | Microchip Technology |
| 文件页数： | 84/84页 |
| 文件大小： | 0K |
| 描述： | IC PIC MCU FLASH 64KB 64-TQFP |
| 标准包装： | 160 |
| 系列： | PIC® 24H |
| 核心处理器： | PIC |
| 芯体尺寸： | 16-位 |
| 速度： | 40 MIP |
| 连通性： | CAN，I²C，IrDA，LIN，SPI，UART/USART |
| 外围设备： | 欠压检测/复位，DMA，POR，PWM，WDT |
| 输入/输出数： | 53 |
| 程序存储器容量： | 64KB（22K x 24） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 8K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 3 V ~ 3.6 V |
| 数据转换器： | A/D 18x10b/12b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 64-TQFP |
| 包装： | 托盘 |
| 产品目录页面： | 648 (CN2011-ZH PDF) |
| 配用： | 876-1004-ND - PIC24 BREAKOUT BOARD |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页当前第84页
2010 Microchip Technology Inc.
DS70152H-page 9
dsPIC33F/PIC24H PROGRAMMING SPECIFICATION
3.2
Confirming the Presence of the
Programming Executive
Before programming, the programmer must confirm
that the programming executive is stored in executive
memory. The procedure for this task is illustrated in
First, ICSP mode is entered. Then, the unique
Application ID Word stored in executive memory is read.
If the programming executive is resident, the correct
Application ID Word is read and programming can
resume as normal. However, if the Application ID Word is
not present, the programming executive must be
programmed to executive code memory using the
method described in Section 6.0 “Programming the
for the Application ID of each device.
Section 5.0 “Device Programming – ICSP” describes
the ICSP programming method. Section 5.11 “Reading
the Application ID Word” describes the procedure for
reading the Application ID Word in ICSP mode.
FIGURE 3-2:
CONFIRMING PRESENCE
OF PROGRAMMING
EXECUTIVE
3.3
Entering Enhanced ICSP Mode
As illustrated in Figure 3-3, entering Enhanced ICSP
Program/Verify mode requires three steps:
1.
The MCLR pin is briefly driven high then low.
2.
A 32-bit key sequence is clocked into PGDx.
3.
MCLR is then driven high within a specified
period of time and held.
The programming voltage applied to MCLR is VIH,
which is essentially VDD in case of dsPIC33F/PIC24H
devices. There is no minimum time requirement for
holding at VIH. After VIH is removed, an interval of at
least P18 must elapse before presenting the key
sequence on PGDx.
The key sequence is a specific 32-bit pattern,
‘0100 1101 0100 0011 0100 1000 0101 0000’
(more
easily
remembered
as
0x4D434850
in
hexadecimal format). The device will enter Program/
Verify mode only if the key sequence is valid. The Most
Significant bit (MSb) of the most significant nibble must
be shifted in first.
Once the key sequence is complete, VIH must be
applied to MCLR and held at that level for as long as
Program/Verify mode is to be maintained. An interval
time of at least P19 and P7 must elapse before
presenting data on PGDx. Signals appearing on PGDx
before P7 has elapsed will not be interpreted as valid.
On successful entry, the program memory can be
accessed and programmed in serial fashion. While in
the Program/Verify mode, all unused I/Os are placed in
the high-impedance state.
Is
Start
Enter ICSP Mode
Application ID
present?(1)
Yes
No
Application ID
Check the
be Programmed
Prog. Executive must
by reading Address
0x8007F0
End
Exit ICSP Mode
Enter Enhanced
Sanity Check
Note 1: See TABLE 7-1: “Device IDs and Revi-
sion” for the Application ID of each
device.
ICSP Mode
Note:
When programming a device without
Peripheral Pin Select (PPS) and in
Enhanced ICSP mode, the SPI output pin
(SDOx) may toggle while the device is
being programmed.
相关PDF资料 |
PDF描述 |
|---|---|
| V300C15H150BL | CONVERTER MOD DC/DC 15V 150W |
| PIC24FJ64GA108-I/PT | MCU PIC 64KB FLASH 80TQFP |
| D38999/24FF32SN | CONN RCPT 32POS JAM NUT W/SCKT |
| D38999/24WD97PA | CONN RCPT 12POS JAM NUT W/PINS |
| D38999/26FC4PA | CONN PLUG 4POS STRAIGHT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PIC24HJ64GP506AT-I/MR | 功能描述:16位微控制器 - MCU 16 Bit MCU 64LD 40MIPS 64KB FLASH RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT |
| PIC24HJ64GP506AT-I/PT | 功能描述:16位微控制器 - MCU 16 Bit MCU 40MIPS 64KB FLASH RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT |
| PIC24HJ64GP506-E/PT | 功能描述:16位微控制器 - MCU 16B MCU 64LD 40MIPS 64KB FLASH RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT |
| PIC24HJ64GP506-I | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:High-Performance, 16-Bit Microcontrollers |
| PIC24HJ64GP506-I/PT | 功能描述:16位微控制器 - MCU 16 Bit MCU 64LD 40 MIPS 64KB Flash RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。