参数资料
型号: PIC32MX795F512HT-80I/PT
厂商: Microchip Technology
文件页数: 14/64页
文件大小: 0K
描述: IC MCU 32BIT 512KB FLASH 64TQFP
标准包装: 1,200
系列: PIC® 32MX
核心处理器: MIPS32? M4K?
芯体尺寸: 32-位
速度: 80MHz
连通性: CAN,以太网,I²C,SPI,UART/USART,USB OTG
外围设备: 欠压检测/复位,DMA,POR,PWM,WDT
输入/输出数: 53
程序存储器容量: 512KB(512K x 8)
程序存储器类型: 闪存
RAM 容量: 128K x 8
电压 - 电源 (Vcc/Vdd): 2.3 V ~ 3.6 V
数据转换器: A/D 16x10b
振荡器型: 内部
工作温度: -40°C ~ 85°C
封装/外壳: 64-TQFP
包装: 带卷 (TR)
2007-2012 Microchip Technology Inc.
DS61145K-page 21
PIC32MX
8.0
CHECK DEVICE STATUS
Before a device can be programmed, the programmer
must check the status of the device to ensure that it is
ready to receive information.
FIGURE 8-1:
CHECK DEVICE STATUS
8.1
4-wire Interface
Four-wire JTAG programming is a Mission mode
operation and therefore the setup sequence to begin
programing should be done while asserting MCLR.
Holding the device in Reset prevents the processor
from executing instructions or driving ports.
The following steps are required to check the device
status using the 4-wire interface:
1.
Set MCLR pin low.
2.
SetMode (6’b011111) to force the Chip TAP
controller into Run Test/Idle state.
3.
SendCommand
(MTAP_SW_MTAP).
4.
SendCommand
(MTAP_COMMAND).
5.
statusVal = XferData (MCHP_STATUS).
6.
If CFGRDY (statusVal<3>) is not ‘1’ and
FCBUSY (statusVal<2>) is not ‘0’ GOTO step 5.
8.2
2-wire Interface
The following steps are required to check the device
status using the 2-wire interface:
1.
SetMode (6’b011111) to force the Chip TAP
controller into Run Test/Idle state.
2.
SendCommand
(MTAP_SW_MTAP).
3.
SendCommand
(MTAP_COMMAND).
4.
statusVal = XferData (MCHP_STATUS).
5.
If CFGRDY (statusVal<3>) is not ‘1’ and
FCBUSY (statusVal<2>) is not ‘0’, GOTO
step 4.
SetMode (6’b011111)
SendCommand
(MTAP_SW_MTAP)
SendCommand
(MTAP_COMMAND)
statusVal = XferData (MCHP_STATUS)
FCBUSY = 0
CFGRDY = 1
No
Set MCLR low
4-wire
Done
Yes
Note:
If using the 4-wire interface, the oscillator
source, as selected by the configuration
words, must be present to access flash
memory. In an unprogrammed device, the
oscillator source is the internal FRC allow-
ing for flash memory access. If the config-
uration words have been reprogrammed
selecting an external oscillator source
then it must be present for flash memory
access. See the “Special Features”
chapter in the specific device data sheet
for details regarding oscillator selection
using the configuration word settings.
Note:
If CFGRDY and FCBUSY do not come to
the proper state within 10 ms, the
sequence may
have
been
executed
incorrectly or the device is damaged.
相关PDF资料
PDF描述
P51-750-A-AF-I12-4.5OVP-000-000 SENSOR 750PSI 9/16-18 UNF 4.5V
P51-3000-A-D-I36-5V-000-000 SENS 3000PSI 22MM 7/16-20 UNF 5V
REC5-053.3DRW/H2/A/M/SMD/CTRL-R CONV DC/DC 5W 4.5-9VIN +/-3.3V
P51-100-S-J-I12-4.5OVP-000-000 SENSOR 100PSI 3/8-24 UNF .5-4.5V
P51-300-G-O-P-4.5V-000-000 SENSOR 300PSI 7/16-20UNF 2B 4.5V
相关代理商/技术参数
参数描述
PIC32MX795F512HT-80V/MR 功能描述:32位微控制器 - MCU 512KB 128KBR USB-OTG 2 CAN ETH 80MHz 10b RoHS:否 制造商:Texas Instruments 核心:C28x 处理器系列:TMS320F28x 数据总线宽度:32 bit 最大时钟频率:90 MHz 程序存储器大小:64 KB 数据 RAM 大小:26 KB 片上 ADC:Yes 工作电源电压:2.97 V to 3.63 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:LQFP-80 安装风格:SMD/SMT
PIC32MX795F512HT-80V/PT 功能描述:32位微控制器 - MCU 512KB 128KBR USB-OTG 2 CAN ETH 80MHz 10b RoHS:否 制造商:Texas Instruments 核心:C28x 处理器系列:TMS320F28x 数据总线宽度:32 bit 最大时钟频率:90 MHz 程序存储器大小:64 KB 数据 RAM 大小:26 KB 片上 ADC:Yes 工作电源电压:2.97 V to 3.63 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:LQFP-80 安装风格:SMD/SMT
PIC32MX795F512L 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:High-Performance, USB, CAN and Ethernet 32-bit Flash Microcontrollers
PIC32MX795F512L-80I/BG 功能描述:32位微控制器 - MCU 512KB Flash 128KB USB ENET RoHS:否 制造商:Texas Instruments 核心:C28x 处理器系列:TMS320F28x 数据总线宽度:32 bit 最大时钟频率:90 MHz 程序存储器大小:64 KB 数据 RAM 大小:26 KB 片上 ADC:Yes 工作电源电压:2.97 V to 3.63 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:LQFP-80 安装风格:SMD/SMT
PIC32MX795F512L-80I/PF 功能描述:32位微控制器 - MCU 512KB Flash 128KBRAM USB 2xCAN 8 DMA RoHS:否 制造商:Texas Instruments 核心:C28x 处理器系列:TMS320F28x 数据总线宽度:32 bit 最大时钟频率:90 MHz 程序存储器大小:64 KB 数据 RAM 大小:26 KB 片上 ADC:Yes 工作电源电压:2.97 V to 3.63 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:LQFP-80 安装风格:SMD/SMT