- 您现在的位置：买卖IC网 > PDF目录98052 > PIM200FZ (LINEAGE POWER LLC) 1-OUTPUT 7.92 W DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | PIM200FZ |
| 厂商： | LINEAGE POWER LLC |
| 元件分类： | 电源模块 |
| 英文描述： | 1-OUTPUT 7.92 W DC-DC REG PWR SUPPLY MODULE |
| 封装： | ROHS COMPLIANT PACKAGE-13 |
| 文件页数： | 2/18页 |
| 文件大小： | 346K |
| 代理商： | PIM200FZ |
Data Sheet
October 5, 2009
PIM200X Series; ATCA Board Power Input Modules
-38 to -75Vdc; 200W Input
LINEAGE POWER
10
Design Considerations
Introduction
The PIM200X module is designed to support the
Advanced Telecommunications Computing
Architecture (ATCA) power entry distribution
requirements for the Front Board / Blade per the
PICMG 3.0 specifications.
The PICMG 3.0 specification defines the Mechanical,
Shelf Management Interface, Power Distribution,
Thermal, Data I/O and Regulatory requirements for
the next generation of modular telecom architecture
platform for use in Central Office telecom
environments.
Input Pin Connections
The ATCA board is specified to accept up to a
maximum of 200W of input power via dual, redundant
-48Vdc Feeds through the Zone 1 (Power and
Management) Positronic connector, designated P10.
The power connector provides board to backplane
engagement via pins of varying lengths. Please
consult the PICMG 3.0 specifications for details.
The following are the design considerations of the
input pin connections of the PIM200X to the ATCA
power connector.
From
ATCA
(P10 Connector)
To
PIM200X
Pin
#
Pin
Designation
Connection
Requirement
Pin
#
Pin
Designation
33
-48V_A
Via Fuse(F3)
1
-48V_AF
34
-48V_B
Via Fuse(F4)
2
-48V_BF
28
VRTN_A
Via Fuse(F1)
3
VRTN_AF
29
VRTN_B
Via Fuse(F2)
4
VRTN_BF
30
EARLY_A*
Via
Resistor(R1)
1
-48V_AF
31
EARLY_B*
Via
Resistor(R2)
2
-48V_BF
32
ENABLE_A
Via Fuse(F5)
5
ENABLE_AF
27
ENABLE_B
Via Fuse(F6)
6
ENABLE_BF
26
LOGIC_GND
Direct
11
LOGIC_GND
25
SHELF_GND
Direct
7
SHELF_GND
* Optional
The first pins to mate in the ATCA power connector
are the EARLY_A, EARLY_B, the two grounds
(LOGIC_GND, SHELF_GND) and the two returns
(VRTN_A, VRTN_B); followed by staggered
connections of -48V_A and -48V_B power Feeds. The
last pins to engage are the two short pins, ENABLE_A
& ENABLE_B. The ATCA backplane connects the
ENABLE_A to VRTN_A, ENABLE_B to VRTN_B,
EARLY_A to -48V_A and EARLY_B to -48V_B.
Optional EARLY_A & EARLY_B Connections:
During hot insertion of the ATCA board, the Inrush
Control circuit limits the surge current to the C_FLTR
capacitor. However, due to the presence of a small
amount of EMI filter capacitance (located before the
Inrush Control circuit), there is a possibility of a surge
current that results in a voltage sag for 5 to 10
microseconds. In most cases this should not be of
concern because all the ATCA Boards and FRU’s on
the -48V bus should be able to ride thru a
5msec/0Volt transient event per the PICMG 3.0
specifications. In case this is undesirable, it is
recommended that Precharge resistors, R1 & R2 (15
Ohms) should be connected as described in the
Typical Application circuit.
Output Pin Connections
The out pin connections of the PIM200X to the
system board is described below:
From
PIM200X
To
Board
Pin
#
Pin
Designation
Terminal
Component
Notes
9
-48V_OUT
Vin(-)
DC/DC
Converter
(1)
13
VRTN_OUT
Vin(+)
DC/DC
Converter
(1)
8
72V_CAP
+ve
C_HLDP
(2)
10
MGMT_PWR
Vcc
(3)
12
-48V_ALARM
IPM/
System Controller
(4)
Notes:
(1) -48V Main Output Bus:
(Signal Names: -48V_OUT & VRTN_OUT)
This is the main -48V output bus that provides the
payload power to the downstream (one or more)
DC/DC converters. The PIM200X module does not
regulate or provide isolation from the input -48V A/B
feeds.
The main functionality of the module is to provide -
48V A/B Feeds OR’ing, inrush protection for hot swap
capability and EMI filtering to attenuate the noise
generated by the downstream DC/DC converters.
The -48V_OUT pin connects to the Vin(-) pin
and the VRTN_OUT pin connects to the
Vin(+) pin of the DC/DC converter(s).
相关PDF资料 |
PDF描述 |
|---|---|
| PIM300FZ | 2-OUTPUT 7.9 W DC-DC REG PWR SUPPLY MODULE |
| PIM300F6Z | 2-OUTPUT 7.9 W DC-DC REG PWR SUPPLY MODULE |
| PIP201-12M-3,518 | 200 A SWITCHING REGULATOR, PQCC68 |
| PIP201-12M | SPECIALTY ANALOG CIRCUIT, PQCC68 |
| PIP8000FHN/N1 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC28 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PIM213 | 功能描述:AUTOMATION HAT (INDIVIDUAL) 制造商:pimoroni ltd 系列:- 零件状态:在售 平台:Raspberry Pi 类型:接口 功能:自动化 使用的 IC/零件:- 内容:板 标准包装:1 |
| PIM215 | 功能描述:PICADE HAT (HAT ONLY) 制造商:pimoroni ltd 系列:- 零件状态:在售 平台:Raspberry Pi 类型:接口 功能:弓形板 使用的 IC/零件:- 内容:板 标准包装:1 |
| PIM216 | 功能描述:MOTE PHAT 制造商:pimoroni ltd 系列:- 零件状态:在售 平台:Raspberry Pi 类型:电源管理 功能:LED 驱动器 使用的 IC/零件:- 内容:板 标准包装:1 |
| PIM221 | 功能描述:AUTOMATION PHAT 制造商:pimoroni ltd 系列:- 零件状态:在售 平台:Raspberry Pi 类型:接口 功能:自动化 使用的 IC/零件:- 内容:板 标准包装:1 |
| PIM242 | 功能描述:RAINBOW HAT (RAINBOW HAT ONLY) 制造商:pimoroni ltd 系列:- 零件状态:在售 平台:Raspberry Pi 类型:接口 功能:多重 使用的 IC/零件:- 内容:板 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。