- 您现在的位置：买卖IC网 > PDF目录18746 > PIXIE-SO-PXSR (Flexipanel)MODULE ZIGBEE SW ROUTER 26SMD PDF资料下载
参数资料
| 型号： | PIXIE-SO-PXSR |
| 厂商： | Flexipanel |
| 文件页数： | 8/13页 |
| 文件大小： | 0K |
| 描述： | MODULE ZIGBEE SW ROUTER 26SMD |
| 标准包装： | 1 |
| 系列： | Pixie™ |
| 频率： | 2.4GHz |
| 调制或协议： | 802.15.4 Zigbee |
| 功率 - 输出： | 0dBm |
| 电源电压： | 2.1 V ~ 3.6 V |
| 电流 - 接收： | 25mA |
| 电流 - 传输： | 25mA |
| 数据接口： | PCB，表面贴装 |
| 存储容量： | 64kB ROM，3986B RAM |
| 天线连接器： | 板载，跟踪 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 26-SMD |
| 包装： | 管件 |
| 产品目录页面： | 560 (CN2011-ZH PDF) |
| 其它名称： | 658-1005-5 |
A high location is recommended, particularly for
avoiding interference from transient objects such as
passers-by and their cellphones. Microwave ovens are
particularly problematic for the short periods in which
they and operational. Where possible, orient all the
antennas in the same direction so that their
polarizations are the same. In a mesh network, a highly
attenuating medium such as a floor may be bridged by
placing two routers close to each other, one on either
side of the barrier.
Table 2. Attenuation of typical bulk materials
Material
Reinforced concrete floor
Brick wall with window
Office wall
Metal cabinet
5mm potting compound
Vegetation
Reduces range by factor of
30
1.25
2
3
2-3
1.25 per meter
Compact materials, e.g. humans, have an complex effect,
In general attenuating most noticeably when closest to the antenna.
Mechanical
PCB Layout
4. Press the generate button to create a file of MAC
addresses. When the file is created, dismiss the
Settings… dialog by pressing OK. The file that was
created contains a hex record each MAC address
containing nine RETLW instructions encoding the
address.
5. .Each time programming session, select Load
SQTP file… form the Programmer menu. In each
programming cycle, MPLAB will read one hex
record and inset the values into ROM locations
0x006A to 0x007B. It will then comment out the
line so it is not used again. In this way the MAC
addresses will be automatically allocated in
sequence. NEVER maintain more than one copy of
the SQTP file, otherwise you risk duplicating MAC
addresses.
Radio Frequency
Optimizing RF Performance
For PCB pad layout, refer to the engineering drawing on
page 10. Note how the pads on the main board
protrude out from beneath the module. This provides a
point to apply heat when manually soldering and also for
continuity testing. In addition, the size of the pad
ensures a large reservoir of solder is available to the
actual contact area.
Soldering
If soldered using a reflow oven, the surface mount
module may be treated like a BGA package. The
quality of the joint may be tested by checking for
continuity between the pad on the upper side of the
board and the protruding part of the pad on the main
board.
The recommended reflow profile is shown in figure 8.
Small increases in temperature (no larger than 15oC)
may be needed depending on the density of the main
board. The module should be reflowed one time only.
The integral antenna supplied with Pixie is a modified
quarter wave F antenna with efficiency of approximately
70%. This is comparable to a dipole and about as high
as physically possible. Its radiation pattern is
approximately omnidirectional.
Free space range is approximately 120m. In-building
ranges of 20m to 40m would normally be expected.
The enclosure employed may affect antenna
performance. Avoid the use of metal enclosures. Gray
300
250
200
150
100
Figure 8. Recommended reflow profile
and black plastics should be used with caution. They
often contain carbon, which degrades performance
considerably. To test for the presence of carbon, heat
the plastic in a microwave oven for one minute. If it
melts, it probably contains carbon.
50
0
0
100
200 300
Time, Seconds
400
500
p8
17-Mar-08
Pixie DS481-17
? FlexiPanel Ltd
Patents may apply and/or pending
www.FlexiPanel.com
相关PDF资料 |
PDF描述 |
|---|---|
| TPI A103 | BOOT HOOK FOR TPI DMM'S |
| DZ-10G-1B | SWITCH BASIC DPDT 10A 570GF |
| A41-80-12 | XFRMR PWR 12.6VCT 6.3A QC .187 |
| IXFT30N50Q3 | MOSFET N-CH 500V 30A TO-268 |
| 10-1 | XFRMR PWR 115V 10VCT 1A |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PIXLITE-DIL-PLFE | 功能描述:MODULE ZIGBEE SW FAST 24-DIP RoHS:是 类别:RF/IF 和 RFID >> RF 收发器 系列:Pixie™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:30 系列:- 频率:4.9GHz ~ 5.9GHz 数据传输率 - 最大:54Mbps 调制或协议:* 应用:* 功率 - 输出:-3dBm 灵敏度:- 电源电压:2.7 V ~ 3.6 V 电流 - 接收:* 电流 - 传输:* 数据接口:PCB，表面贴装 存储容量:- 天线连接器:PCB，表面贴装 工作温度:-25°C ~ 85°C 封装/外壳:68-TQFN 裸露焊盘 包装:管件 |
| PIXLITE-DIL-PLSE | 功能描述:MODULE ZIGBEE SW SLEEPY 24DIP RoHS:是 类别:RF/IF 和 RFID >> RF 收发器 系列:Pixie™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:30 系列:- 频率:4.9GHz ~ 5.9GHz 数据传输率 - 最大:54Mbps 调制或协议:* 应用:* 功率 - 输出:-3dBm 灵敏度:- 电源电压:2.7 V ~ 3.6 V 电流 - 接收:* 电流 - 传输:* 数据接口:PCB，表面贴装 存储容量:- 天线连接器:PCB，表面贴装 工作温度:-25°C ~ 85°C 封装/外壳:68-TQFN 裸露焊盘 包装:管件 |
| PIXLITE-SO-PLFE | 功能描述:Zigbee/802.15.4模块 Pixie Zigbee Mod SO Fast End Device FW RoHS:否 制造商:Digi International 频带:902 MHz to 928 MHz 视线范围: 数据速率: 灵敏度: 工作电源电压:2.4 V to 3.6 V 传输供电电流:215 mA 接收供电电流:26 mA 输出功率:250 mW 天线连接器类型:Wire 最大工作温度:+ 85 C 尺寸:32.94 mm x 22 mm x 2.03 mm |
| PIXLITE-SO-PLSE | 功能描述:Zigbee/802.15.4模块 Pixie Zigbee Mod SO Sleepy End Device FW RoHS:否 制造商:Digi International 频带:902 MHz to 928 MHz 视线范围: 数据速率: 灵敏度: 工作电源电压:2.4 V to 3.6 V 传输供电电流:215 mA 接收供电电流:26 mA 输出功率:250 mW 天线连接器类型:Wire 最大工作温度:+ 85 C 尺寸:32.94 mm x 22 mm x 2.03 mm |
| PIXZEELITE | 制造商:RF Solutions LTD 功能描述:MODULE MINI ZIGBEE IEEE 802.15.4 |
发布紧急采购，3分钟左右您将得到回复。