- 您现在的位置：买卖IC网 > PDF目录69047 > PKB4418PIPOANBLB (ERICSSON POWER MODULES AB) 1-OUTPUT 45 W DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | PKB4418PIPOANBLB |
| 厂商： | ERICSSON POWER MODULES AB |
| 元件分类： | 电源模块 |
| 英文描述： | 1-OUTPUT 45 W DC-DC REG PWR SUPPLY MODULE |
| 文件页数： | 11/23页 |
| 文件大小： | 367K |
| 代理商： | PKB4418PIPOANBLB |
19
EN/LZT 146 033 R1D Ericsson Power Modules, June 2004
PKB 4000 Datasheet
Operating Information
Input Voltage
The input voltage range 36…75Vdc meets the requirements
of the European Telecom Standard ETS 300 132-2 for normal
input voltage range in –48V and –60V DC systems, -40.5…-
57.0V and –50.0…-72V respectively. At input voltages
exceeding 75V, the power loss will be higher than at normal
input voltage and TPcb must be limited to absolute max
+110
°C. The absolute maximum continuous input voltage
is 80Vdc.
Turn-Off Input Voltage
The PKB 4000 Series DC/DC converters monitor the input
voltage and will turn on and turn off at predetermined levels.
The minimum hysteresis between turn on and turn off input
voltage is 1V where the turn on input voltage is the highest.
Output Voltage Adjust (Vadj)
All PKB 4000 Series DC/DC converters have an Output
Voltage adjust pin (Vadj). This pin can be used to adjust the
output voltage above or below Output voltage initial setting.
When increasing the output voltage, the voltage at the output
pins (including any remote sense offset) must be kept below
the overvoltage trip point, to prevent the converter from
shut down. Also note that at increased output voltages the
maximum power rating of the converter remains the same, and
the output current capability will decrease correspondingly. To
decrease the output voltage the resistor should be connected
between Vadj pin and –Sense pin. To increase the voltage the
resistor should be connected between Vadj pin and +Sense
pin. The resistor value of the Output voltage adjust function is
according to information given under the output section.
Remote Control (RC)
All PKB 4000 Series DC/DC converters have remote sense that
can be used to compensate for moderate amounts of resistance
in the distribution system and allow for voltage regulation at
the load or other selected point. The remote sense lines will
carry very little current and do not need a large cross sectional
area. However, the sense lines on the PCB should be located
close to a ground trace or ground plane. In a discrete wiring
situation, the use of twisted pair wires or other technique to
reduce noise susceptibility is highly recommended. The remote
sense circuitry will compensate for up to 10% voltage drop
between the sense voltage and the voltage at the output pins.
The output voltage and the remote sense voltage offset must be
less than the minimum over voltage trip point. If the remote
sense is not needed the –Sense should be connected to –Out and
+Sense should be connected to +Out.
Remote Sense
Circuit conguration for output voltage adjust
+Out
-Out
+Sense
Vadj
-Sense
Load
Radj
Decrease
Load
Increase
+Out
-Out
+Sense
Vadj
-Sense
The PKB 4000 Series DC/DC
converters have a remote control
function referenced to the primary side
(- In), with negative and positive logic
options available. The RC function
allows the converter to be turned
on/off by an external device like a
semiconductor or mechanical switch.
The RC pin has an internal pull up resistor to + In. The needed
maximum sink current is 1mA. When the RC pin is left
open, the voltage generated on the RC pin is 12 - 15 V. The
maximum allowable leakage current of the switch is 20
A.
The standard converter is provided with “negative logic”
remote control and the converter will be off until the RC pin
is connected to the - In. To turn on the converter the voltage
between RC pin and - In should be less than 1V. To turn off
the converter the RC pin should be left open, or connected to a
voltage higher than 13 V referenced to - In. In situations where
it is desired to have the converter to power up automatically
without the need for control signals or a switch, the RC pin
can be wired directly to - In.
The second option is “positive logic” remote control, which
can be ordered by adding the suffix “P” to the end of the part
number. The converter will turn on when the input voltage
is applied with the RC pin open. Turn off is achieved by
connecting the RC pin to the - In. To ensure safe turn off the
voltage difference between RC pin and the - In pin shall be less
than 1V. The converter will restart automatically when this
connection is opened.
Circuit conguration
for RC function
+In
RC
-In
相关PDF资料 |
PDF描述 |
|---|---|
| PKB4418PIPOANBM | 1-OUTPUT 45 W DC-DC REG PWR SUPPLY MODULE |
| PKB4418PIPOANBMLA | 1-OUTPUT 45 W DC-DC REG PWR SUPPLY MODULE |
| PKB4318PIPOBNBLA | 1-OUTPUT 36 W DC-DC REG PWR SUPPLY MODULE |
| PKB4418PIPOANBLA | 1-OUTPUT 45 W DC-DC REG PWR SUPPLY MODULE |
| PKB4318PIPOBNBMLA | 1-OUTPUT 36 W DC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PKB4418SIOANB | 制造商:Ericsson 功能描述:- Trays |
| PKB4513PINBLC | 功能描述:DC/DC 开关控制器 DC/DC CONV in 36-60V output 12V 4A 48W RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| PKB4513PINBOVL | 制造商:Ericsson 功能描述: |
| PKB4513PINBOVLC | 制造商:Ericsson 功能描述:- Trays |
| PKB4519PINB | 制造商:ERIC 功能描述: |
发布紧急采购，3分钟左右您将得到回复。