- 您现在的位置：买卖IC网 > PDF目录69047 > PKB4913PIPNBM (ERICSSON POWER MODULES AB) 1-OUTPUT 90 W DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | PKB4913PIPNBM |
| 厂商： | ERICSSON POWER MODULES AB |
| 元件分类： | 电源模块 |
| 英文描述： | 1-OUTPUT 90 W DC-DC REG PWR SUPPLY MODULE |
| 封装： | ROHS COMPLIANT, PACKAGE-8 |
| 文件页数： | 33/42页 |
| 文件大小： | 2514K |
| 代理商： | PKB4913PIPNBM |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页当前第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页
Operating Information
Over Temperature Protection (OTP)
The PKB 4000 Series DC/DC converters are protected from thermal
overload by an internal over temperature shutdown circuit . When
the PCB temperature on the topside between the signal transformer
and output choke (position P1 as defined in Thermal consideration
section) exceeds 120 °C the converter will shut down immediately.
The converter will make continuous attempts to start up (non-
latching mode) and resume normal operation automatically when the
temperature has dropped >10 C below the temperature threshold.
Input And Output Impedance
The impedance of both the power source and the load will interact
with the impedance of the DC/DC converter. It is most important
to have a low characteristic impedance, both at the input and
output, as the converters have a low energy storage capability.
The PKB 4000 Series DC/DC converters have been designed to be
completely stable without the need for external capacitors on the
input or the output circuits . The performance in some applications
can be enhanced by addition of external capacitance as described
under maximum capacitive load . If the distribution of the input
voltage source to the converter contains significant inductance, the
addition of a 100 F capacitor across the input of the converter will
help insure stability. This capacitor is not required when powering
the DC/DC converter from a low impedance source with short, low
inductance, input power leads .
Parallel Operation
The PKB 4000 Series DC/DC converters can be paralleled for redun-
dancy if external o-ring diodes are used in series with the outputs .
It is not recommended to parallel the PKB 4000 Series DC/DC
converters for increased power without using external current shar-
ing circuits .
Maximum Capacitive Load
When powering loads with significant dynamic current requirements,
the voltage regulation at the load can be improved by addition of
decoupling capacitance at the load . The most affective technique
is to locate low ESR ceramic capacitors as close to the load as
possible, using several capacitors to lower the effective ESR .
These ceramic capacitors will handle short duration high-frequency
components of dynamic load changes . In addition, higher values of
electrolytic capacitors should be used to handle the mid-frequency
components . It is equally important to use good design practise
when configuring the DC distribution system .
Low resistance and low inductance PCB layouts and cabling should
be used . Remember that when using remote sensing, all resistance,
inductance and capacitance of the distribution system is within the
feedback loop of the converter. This can affect on the converters
compensation and the resulting stability and dynamic response
performance . As a “rule of thumb”, 100F/A of output current can
be used without any additional analysis . For example with a 25A
converter, values of decoupling capacitance up to 2500 F can be
used without regard to stability. With larger values of capacitance,
the load transient recovery time can exceed the specified value . As
much of the capacitance as possible should be outside the remote
sensing loop and close to the load . The absolute maximum value of
output capacitance is 10 000 F. For values larger than this, please
contact your local Ericsson Power Modules representative .
Current Limit Protection
The PKB 4000 Series DC/DC converters include current limiting
circuitry that allows them to withstand continuous overloads or short
circuit conditions on the output . The output voltage will decrease
towards zero for output currents in excess of max output current
(Iomax) .
The converter will resume normal operation after removal of the
overload . The load distribution system should be designed to carry
the maximum output short circuit current specified .
Over Voltage Protection (OVP)
The PKB 4000 Series DC/DC converters have output overvoltage
protection . In the event of an overvoltage condition, the converter
will shut down immediately. The converter will make continuous at-
tempts to start up (non-latching mode) and resume normal operation
automatically.
EN/LZT 146 033 R9A Ericsson Power Modules, March 2007
PKB 4000 Datasheet
39
相关PDF资料 |
PDF描述 |
|---|---|
| PKB4913PIPNBLA | 1-OUTPUT 90 W DC-DC REG PWR SUPPLY MODULE |
| PKB4418PIOAPNBLA | 1-OUTPUT 45 W DC-DC REG PWR SUPPLY MODULE |
| PKB4619PIPNBLA | 1-OUTPUT 62.5 W DC-DC REG PWR SUPPLY MODULE |
| PKB4610PIPNBMLA | 1-OUTPUT 66 W DC-DC REG PWR SUPPLY MODULE |
| PKB4713PIPNBM | 1-OUTPUT 72 W DC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PKB4913SINB | 功能描述:DC/DC转换器 90W 12V 7.5A 36-75Vin SMT RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| PKB4918HCPI | 功能描述:DC/DC转换器 1.5Vdc 60A Isolated Input 36-75V 90W RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| PKB4918LCPI | 功能描述:DC/DC转换器 1.2Vdc 50A Isolated Input 36-75V 60W RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| PKB5713PINB | 制造商:Ericsson 功能描述:PKB 1/8TH-BRICK SERIES ISOLATED, THRU-HOLE, CONVERTER - Trays |
| PKB-632 | 制造商:STANDARD INSERTS 功能描述: |
发布紧急采购，3分钟左右您将得到回复。