- 您现在的位置：买卖IC网 > PDF目录69047 > PKB4913PIPNBMLB (ERICSSON POWER MODULES AB) 1-OUTPUT 90 W DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | PKB4913PIPNBMLB |
| 厂商： | ERICSSON POWER MODULES AB |
| 元件分类： | 电源模块 |
| 英文描述： | 1-OUTPUT 90 W DC-DC REG PWR SUPPLY MODULE |
| 封装： | ROHS COMPLIANT, PACKAGE-8 |
| 文件页数： | 39/42页 |
| 文件大小： | 2514K |
| 代理商： | PKB4913PIPNBMLB |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页当前第39页第40页第41页第42页
Ericsson Power Modules DC/DC converters and DC/DC regulators
are designed in accordance with safety standards
IEC/EN/UL 60 950, Safety of Information Technology Equipment.
IEC/EN/UL60950 contains requirements to prevent injury or
damage due to the following hazards:
Electrical shock
Energy hazards
Fire
Mechanical and heat hazards
Radiation hazards
Chemical hazards
On-board DC-DC converters are defined as component power
supplies . As components they cannot fully comply with the
provisions of any Safety requirements without “Conditions of
Acceptability” . It is the responsibility of the installer to ensure that
the final product housing these components complies with the
requirements of all applicable Safety standards and Directives for
the final product .
Component power supplies for general use should comply with
the requirements in IEC60950, EN60950 and UL60950 “Safety of
information technology equipment” .
There are other more product related standards, e .g .
IEC61204-7 “Safety standard for power supplies",
IEEE802 .3af “Ethernet LAN/MAN Data terminal equipment
power”, and ETS300132-2 “Power supply interface at the input to
telecommunications equipment; part 2: DC”,
but all of these standards are based on IEC/EN/UL60950 with
regards to safety.
Ericsson Power Modules DC/DC converters and DC/DC regulators
are UL 60 950 recognized and certified in accordance with EN 60
950 .
The flammability rating for all construction parts of the products
meets UL 94V-0 .
The products should be installed in the end-use equipment, in
accordance with the requirements of the ultimate application .
Normally the output of the DC/DC converter is considered as SELV
(Safety Extra Low Voltage) and the input source must be isolated by
minimum Double or Reinforced Insulation from the primary circuit
(AC mains) in accordance with IEC/EN/UL 60 950 .
Safety Specification
Isolated DC/DC converters .
The input voltage to the DC/DC regulator is SELV (Safety Extra Low
Voltage) and the output remains SELV under normal and abnormal
operating conditions .
It is recommended that a slow blow fuse with a rating
twice the maximum input current per selected product
be used at the input of each DC/DC regulator.
Non-isolated DC/DC regulators .
24 V dc systems .
The input voltage to the DC/DC converter is SELV (Safety Extra Low
Voltage) and the output remains SELV under normal and abnormal
operating conditions .
48 and 60 V dc systems .
If the input voltage to Ericsson Power Modules DC/DC converter
is 75 V dc or less, then the output remains SELV (Safety Extra Low
Voltage) under normal and abnormal operating conditions .
Single fault testing in the input power supply circuit should be
performed with the DC/DC converter connected to demonstrate
that the input voltage does not exceed 75 V dc .
If the input power source circuit is a DC power system, the source
may be treated as a TNV2 circuit and testing has demonstrated
compliance with SELV limits and isolation requirements equivalent
to Basic Insulation in accordance with IEC/EN/UL 60 950 .
It is recommended that a fast blow fuse with a rating
twice the maximum input current per selected product
be used at the input of each DC/DC converter. If an input filter is
used in the circuit the fuse should be placed in front of the input
filter.
In the rare event of a component problem in the input filter or in the
DC/DC converter that imposes a short circuit on the input source,
this fuse will provide the following functions:
Isolate the faulty DC/DC converter from the input power source
so as not to affect the operation of other parts of the system .
Protect the distribution wiring from excessive current and power
loss thus preventing hazardous overheating .
The galvanic isolation is verified in an electric strength test . The test
voltage (VISO) between input and output is 1500 Vdc or 2250 Vdc for
60 seconds (refer to product specification) . Leakage current is less
than 1A at nominal input voltage .
General information .
EN/LZT 146 033 R9A Ericsson Power Modules, March 2007
PKB 4000 Datasheet
6
相关PDF资料 |
PDF描述 |
|---|---|
| PKB4610PIPNBLB | 1-OUTPUT 66 W DC-DC REG PWR SUPPLY MODULE |
| PKB4619PINBMLA | 1-OUTPUT 62.5 W DC-DC REG PWR SUPPLY MODULE |
| PKB4913PIPNBM | 1-OUTPUT 90 W DC-DC REG PWR SUPPLY MODULE |
| PKB4913PIPNBLA | 1-OUTPUT 90 W DC-DC REG PWR SUPPLY MODULE |
| PKB4418PIOAPNBLA | 1-OUTPUT 45 W DC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PKB4913SINB | 功能描述:DC/DC转换器 90W 12V 7.5A 36-75Vin SMT RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| PKB4918HCPI | 功能描述:DC/DC转换器 1.5Vdc 60A Isolated Input 36-75V 90W RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| PKB4918LCPI | 功能描述:DC/DC转换器 1.2Vdc 50A Isolated Input 36-75V 60W RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| PKB5713PINB | 制造商:Ericsson 功能描述:PKB 1/8TH-BRICK SERIES ISOLATED, THRU-HOLE, CONVERTER - Trays |
| PKB-632 | 制造商:STANDARD INSERTS 功能描述: |
发布紧急采购，3分钟左右您将得到回复。