- 您现在的位置：买卖IC网 > PDF目录98053 > PKJ2316UPIP (ERICSSON POWER MODULES AB) DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | PKJ2316UPIP |
| 厂商： | ERICSSON POWER MODULES AB |
| 元件分类： | 电源模块 |
| 英文描述： | DC-DC REG PWR SUPPLY MODULE |
| 封装： | ROHS COMPLIANT, HALF-BRICK PACKAGE-9 |
| 文件页数： | 14/14页 |
| 文件大小： | 1573K |
| 代理商： | PKJ2316UPIP |
Ericsson Internal
PRODUCT SPECIFICATION
2 (5)
Prepared (also subject responsible if other)
No.
EQUENXU
3/1301-BMR 630 12/7 Uen
Approved
Checked
Date
Rev
Reference
SEC/D (Julia You)
ESECZHW
2008-01-15
B
Operating information
Input Voltage
The input voltage range 20 to 36Vdc meets the requirements
of the European Telecom Standard ETS 300 132-2 for normal
input voltage range in+24 Vdc systems.
At input voltages exceeding 36 V, the power loss will be
higher than at normal input voltage and T
ref must be limited to
absolute max +120°C. The absolute maximum continuous
input voltage is 40 Vdc.
Turn-off Input Voltage
The DC/DC converters monitor the input voltage and will turn
on and turn off at predetermined levels.
The minimum hysteresis between turn on and turn off input
voltage is 1V.
Remote Control (RC)
The products are fitted with a
remote control function referenced
to the primary negative input
connection (- In), with negative and
positive logic options available.
The RC function allows the
converter to be turned on/off by an
external device like a
semiconductor or mechanical
switch.
The maximum required sink current is 1 mA. When the RC pin
is left open, the voltage generated on the RC pin is
3.5 — 6 V. The second option is “positive logic” remote
control, which can be ordered by adding the suffix “P” to the
end of the part number. The converter will turn on when the
input voltage is applied with the RC pin open. Turn off is
achieved by connecting the RC pin to the - In. To ensure safe
turn off the voltage difference between RC pin and the - In pin
shall be less than 1V. The converter will restart automatically
when this connection is opened.
See Design Note 021 for detailed information.
Input and Output Impedance
The impedance of both the input source and the load will
interact with the impedance of the DC/DC converter. It is
important that the input source has low characteristic
impedance. The converters are designed for stable operation
without external capacitors connected to the input or output.
The performance in some applications can be enhanced by
addition of external capacitance as described under External
Decoupling Capacitors. If the input voltage source contains
significant inductance, the addition of a 100 μF capacitor
across the input of the converter will ensure stable operation.
The capacitor is not required when powering the DC/DC
converter from an input source with an inductance below
10 μH.
External Decoupling Capacitors
When powering loads with significant dynamic current
requirements, the voltage regulation at the point of load can
be improved by addition of decoupling capacitors at the load.
The most effective technique is to locate low ESR ceramic
and electrolytic capacitors as close to the load as possible,
using several parallel capacitors to lower the effective ESR.
The ceramic capacitors will handle high-frequency dynamic
load changes while the electrolytic capacitors are used to
handle low frequency dynamic load changes. Ceramic
capacitors will also reduce any high frequency noise at the
load.
It is equally important to use low resistance and low
inductance PCB layouts and cabling.
External decoupling capacitors will become part of the
control loop of the DC/DC converter and may affect the
stability margins. As a “rule of thumb”, 100 μF/A of output
current can be added without any additional analysis. The
ESR of the capacitors is a very important parameter. Power
Modules guarantee stable operation with a verified ESR value
of >10 mΩ across the output connections.
For further information please contact your local Ericsson
Power Modules representative.
Output Voltage Adjust (Vadj)
The DC/DC converters have an Output Voltage Adjust pin
(Vadj). This pin can be used to adjust the output voltage above
or below Output voltage initial setting.
When increasing the output voltage, the voltage at the output
pins (including any remote sense compensation ) must be
kept below the threshold of the over voltage protection, (OVP)
to prevent the converter from shutting down. At increased
output voltages the maximum power rating of the converter
remains the same, and the max output current must be
decreased correspondingly.
To increase the voltage the resistor should be connected
between the Vadj pin and +Sense pin. The resistor value of the
Output voltage adjust function is according to information
given under the Output section for the respective product.
To decrease the output voltage, the resistor should be
connected between the Vadj pin and —Sense pin.
E
PKJ 2000 series
DC/DC converters, Input 20-36 V, Output 27 V/385 W
EN/LZT 146 392 R1B January 2008
Ericsson Power Modules AB
Technical Specication
E
PKJ 2000 series
DC/DC converters, Input 20-36 V, Output 27 V/385 W
EN/LZT 146 392 R1C August 2008
Ericsson Power Modules AB
Technical Specication
9
相关PDF资料 |
PDF描述 |
|---|---|
| PKJ4110EPIHS | 1-OUTPUT 65 W DC-DC REG PWR SUPPLY MODULE |
| PKJ4110EPILA | 1-OUTPUT 65 W DC-DC REG PWR SUPPLY MODULE |
| PKJ4216NPIT | 1-OUTPUT 250 W DC-DC REG PWR SUPPLY MODULE |
| PKJ4316APILA | 1-OUTPUT 350 W DC-DC REG PWR SUPPLY MODULE |
| PKJ4216NPILA | 1-OUTPUT 250 W DC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PKJ4110BPIT | 功能描述:DC/DC转换器 3.3 Vdc 40A Iso Input 36-75V 132W RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| PKJ4110EPI | 功能描述:DC/DC转换器 3.3 Vdc 30A Iso Input 48V 100W RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| PKJ4110EPILA | 制造商:Ericsson 功能描述:DC/DC PS SGL-OUT 3.3V 30A 100W 9PIN - Bulk |
| PKJ4111APIT | 功能描述:DC/DC转换器 5 Vdc 30A Iso Input 36-75V 150W RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| PKJ4111EPI | 功能描述:DC/DC转换器 5 Vdc 20A Iso Input 48V 100W RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
发布紧急采购，3分钟左右您将得到回复。