- 您现在的位置：买卖IC网 > PDF目录98053 > PKJ4110EPIHS (ERICSSON POWER MODULES AB) 1-OUTPUT 65 W DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | PKJ4110EPIHS |
| 厂商： | ERICSSON POWER MODULES AB |
| 元件分类： | 电源模块 |
| 英文描述： | 1-OUTPUT 65 W DC-DC REG PWR SUPPLY MODULE |
| 封装： | ROHS COMPLIANT PACKAGE-9 |
| 文件页数： | 17/31页 |
| 文件大小： | 1398K |
| 代理商： | PKJ4110EPIHS |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页
Ericsson Internal
PRODUCT SPECIFICATION
2 (6)
Prepared (also subject responsible if other)
No.
KI/EAB/FC/P Anders Wgmark
3/1301-BMR623 Uen
Approved
Checked
Date
Rev
Reference
KM/EAB/FJB/GMF (Natalie Johansson)
(MICMALE)
2008-11-21
B
Operating information
Input Voltage
The input voltage range 36 to 75 Vdc meets the requirements
of the European Telecom Standard ETS 300 132-2 for normal
input voltage range in –48 and –60 Vdc systems, -40.5 to -
57.0 V and –50.0 to -72 V respectively.
At input voltages exceeding 75 V, the power loss will be higher
than at normal input voltage and TP1 must be limited to
absolute max +125°C. The absolute maximum continuous
input voltage is 80 Vdc.
Turn-off Input Voltage
The products monitor the input voltage and will turn on and
turn off at predetermined levels.
The minimum hysteresis between turn on and turn off input
voltage is 1 V.
Remote Control (RC)
The products are fitted with a
remote control function referenced
to the primary negative input
connection (-In), with negative and
positive logic options available.
The RC function allows the product
to be turned on/off by an external
device like a semiconductor or
mechanical switch. The RC pin has
an internal pull up resistor to +In.
The maximum required sink current is 1 mA. When the RC pin
is left open, the voltage generated on the RC pin is
3.5 – 6.0 V. The standard product is provided with “negative
logic” remote control and will be off until the RC pin is
connected to the -In. To turn on the product the voltage
between RC pin and -In should be less than 1V. To turn off the
converter the RC pin should be left open, or connected to a
voltage higher than 4 V referenced to -In. In situations where it
is desired to have the product to power up automatically
without the need for control signals or a switch, the RC pin can
be wired directly to -In.
The second option is “positive logic” remote control, which can
be ordered by adding the suffix “P” to the end of the part
number. When the RC pin is left open, the product starts up
automatically when the input voltage is applied. Turn off is
achieved by connecting the RC pin to the -In. To ensure safe
turn off the voltage difference between RC pin and the -In pin
shall be less than 1V. The product will restart automatically
when this connection is opened.
See Design Note 021 for detailed information.
Input and Output Impedance
The impedance of both the input source and the load will
interact with the impedance of the product. It is important that
the input source has low characteristic impedance. The
products are designed for stable operation without external
capacitors connected to the input or output. The performance
in some applications can be enhanced by addition of external
capacitance as described under External Decoupling
Capacitors.
If the input voltage source contains significant inductance, the
addition of a 22 - 100 F capacitor across the input of the
product will ensure stable operation. The capacitor is not
required when powering the product from an input source with
an inductance below 10 H. The minimum required
capacitance value depends on the output power and the input
voltage. The higher output power the higher input capacitance
is needed. Approximately doubled capacitance value is
required for a 24 V input voltage source compared to a 48V
input voltage source.
External Decoupling Capacitors
When powering loads with significant dynamic current
requirements, the voltage regulation at the point of load can
be improved by addition of decoupling capacitors at the load.
The most effective technique is to locate low ESR ceramic and
electrolytic capacitors as close to the load as possible, using
several parallel capacitors to lower the effective ESR. The
ceramic capacitors will handle high-frequency dynamic load
changes while the electrolytic capacitors are used to handle
low frequency dynamic load changes. It is equally important to
use low resistance and low inductance PCB layouts and
cabling.
External decoupling capacitors will become part of the control
loop of the DC/DC converter and may affect the stability
margins. As a “rule of thumb”, 100 F/A of output current can
be added without any additional analysis. The ESR of the
capacitors is a very important parameter. Power Modules
guarantee stable operation with a verified ESR value of >10
m across the output connections.
For further information please contact your local Ericsson
Power Modules representative.
Output Voltage Adjust (Vadj)
The products have an Output Voltage Adjust pin (Vadj). This
pin can be used to adjust the output voltage above or below
Output voltage initial setting.
When increasing the output voltage, the voltage at the output
pins (including any remote sense compensation ) must be
kept below the threshold of the over voltage protection, (OVP)
to prevent the product from shutting down. At increased output
voltages the maximum power rating of the product remains the
same, and the max output current must be decreased
correspondingly.
To increase the voltage the resistor should be connected
between the Vadj pin and +Sense pin. The resistor value of the
Output voltage adjust function is according to information
given under the Output section for the respective product.
To decrease the output voltage, the resistor should be
connected between the Vadj pin and –Sense pin.
E
PKJ 4000E series
Direct Converters
Input 36-75 V, Output up to 30 A / 100 W
EN/LZT 146 383 R3A September 2009
Ericsson AB
Technical Specication
24
相关PDF资料 |
PDF描述 |
|---|---|
| PKJ4110EPILA | 1-OUTPUT 65 W DC-DC REG PWR SUPPLY MODULE |
| PKJ4216NPIT | 1-OUTPUT 250 W DC-DC REG PWR SUPPLY MODULE |
| PKJ4316APILA | 1-OUTPUT 350 W DC-DC REG PWR SUPPLY MODULE |
| PKJ4216NPILA | 1-OUTPUT 250 W DC-DC REG PWR SUPPLY MODULE |
| PKJ4216PIM | 1-OUTPUT 250 W DC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PKJ4110EPILA | 制造商:Ericsson 功能描述:DC/DC PS SGL-OUT 3.3V 30A 100W 9PIN - Bulk |
| PKJ4111APIT | 功能描述:DC/DC转换器 5 Vdc 30A Iso Input 36-75V 150W RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| PKJ4111EPI | 功能描述:DC/DC转换器 5 Vdc 20A Iso Input 48V 100W RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| PKJ4111EPI-R2J | 制造商:Ericsson 功能描述: |
| PKJ4111PI | 制造商:Ericsson 功能描述:DC/DC PS SGL-OUT 5V 20A 100W - Bulk |
发布紧急采购，3分钟左右您将得到回复。