- 您现在的位置：买卖IC网 > PDF目录69050 > PKJ4510PIP (ERICSSON POWER MODULES AB) 1-OUTPUT 50 W DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | PKJ4510PIP |
| 厂商： | ERICSSON POWER MODULES AB |
| 元件分类： | 电源模块 |
| 英文描述： | 1-OUTPUT 50 W DC-DC REG PWR SUPPLY MODULE |
| 文件页数： | 12/20页 |
| 文件大小： | 617K |
| 代理商： | PKJ4510PIP |
Data Sheet AE/LZT 137 57 R1 Ericsson Components AB, August 1999
Characteristics
min
max
Unit
TC
Maximum Operating Case Temperature
-40
+100
°C
TS
Storage temperature
-40
+125
°C
VI
Continuous input voltage
-0.5
+75
Vdc
VISO Isolation voltage
1,500
Vdc
(input to output test voltage)
VRC Remote control voltage
15
Vdc
I2t
Inrush transient
1
A2s
Characteristics
Conditions
min
typ max
Unit
VI
Input voltage
36
72
Vdc
range1)
VIoff
Turn-off input
Ramping from
31
33
Vdc
voltage
higher voltage
VIon
Turn-on input
Ramping from
34
36
Vdc
voltage
lower voltage
CI
Input capacitance
2.8
F
IIac
Reflected
5 Hz to 20 MHz-150W
20
mA p-p
ripple current
50 W
1.6
IImax
Maximum input
VI = VI min
75 W
2.4
A
current
100 W
3.2
150 W
5.3
PIi
Input idling power
IO = 0
2.5
7.5
W
PRC
Input
stand-by power
VI = 50V
RC open
.05
2.5
W
(turned off with RC)
TRIM
Maximum input
6
Vdc
voltage on trim pin
Characteristics
Test procedure & conditions
Random
IEC 68-2-34Ed
Frequency
10...500 Hz
Vibration
Spectral density
0.025 g2/Hz
Duration
10 min in each
direction
Sinusoidal
IEC 68-2-6 Fc
Frequency
10-500 Hz
Vibration
Amplitude
0.75mm
Acceleration
10g
# of cycles
10 in each axis
Shock
IEC 68-2-27 Ea
Peak acceleration
50 g
(half sinus)
Duration
3ms
Temperature
IEC 68-2-14 Na
Temperature
-40°C...+100°C
change
Number of cycles
300
Accelerated
IEC 68-2-3 Ca
Temperature
85°C
damp heat
with bias
Humidity
85% RH
Duration
500 hours
Solder
IEC 68-2-20 Tb
Temperature, solder
260° C
resistibility
method IA
Duration
10...13 s
General
Absolute Maximum Ratings
Input TC < TCmax
Environmental Characteristics
2
Stress in excess of Absolute Maximum Ratings may
cause permanent damage. Absolute Maximum Ratings,
sometimes referred to as no destruction limits, are
normally tested with one parameter at a time exceeding
the limits of Output data or Electrical Characteristics.
If exposed to stress above these limits, function and
performance may degrade in an unspecified manner.
For design margin and to enhance system reliability,
it is recommended that the PKJ series DC/DC power
modules are operated at case temperatures below 90°C.
1) See also Input Voltage in the Operating
Information section
Safety
The PKJ Series DC/DC power modules are
designed to comply with EN 60 950 Safety of
information technology equipment including
electrical business equipment.
The PKJ DC/DC power modules are also
recognized by UL and meet the applicable
requirements in UL 1950, Safety of information
technology equipment and applicable Canadian
safety requirements.
The isolation is an operational insulation in
accordance with EN 60 950. The DC/DC power
module should be installed in end-use equipment,
in compliance with the requirements of the
ultimate application, and is intended to be
supplied by an isolated secondary circuit.
Consideration should be given to measuring
the case temperature to comply with TCmax
when in operation.
When the supply to the DC/DC power
module meets all the requirements for SELV
(<60Vdc), the output is considered to remain
within SELV limits (level 3). If connected to a 60V
DC power system, reinforced insulation must be
provided in the power supply that isolates the
input from the mains. Single fault testing in the
power supply must be performed in combination
with the DC/DC power module to demonstrate
that the output meets the requirement for SELV.
One pole of the input and one pole of the output
is to be grounded or both are to be kept floating.
相关PDF资料 |
PDF描述 |
|---|---|
| PKJ4711PIP | 1-OUTPUT 75 W DC-DC REG PWR SUPPLY MODULE |
| PKJ4111APIP | 1-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE |
| PKJ4115EPIP | 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
| PKJ4618GEPIP | 1-OUTPUT 65 W DC-DC REG PWR SUPPLY MODULE |
| PKJ4113EPIPLA | 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PKJ4518PIT | 功能描述:DC/DC转换器 1.8 Vdc 30A Iso Input 36-75V 54W RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| PKJ4519PI | 制造商:Ericsson 功能描述:DC/DC PS SGL-OUT 2.5V 20A 50W - Bulk |
| PKJ4519PIP | 制造商:Ericsson 功能描述:DC/DC PS SGL-OUT 2.5V 20A 50W - Bulk |
| PKJ4519PIT | 功能描述:DC/DC转换器 2.5 Vdc 20A Iso Input 36-75V 50W RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| PKJ4618GEPI | 功能描述:DC/DC转换器 1.8 Vdc 36A Iso Input 48V 65W RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
发布紧急采购，3分钟左右您将得到回复。