- 您现在的位置：买卖IC网 > PDF目录69051 > PKL4110PIPTSP (ERICSSON POWER MODULES AB) 1-OUTPUT 165 W DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | PKL4110PIPTSP |
| 厂商： | ERICSSON POWER MODULES AB |
| 元件分类： | 电源模块 |
| 英文描述： | 1-OUTPUT 165 W DC-DC REG PWR SUPPLY MODULE |
| 文件页数： | 12/42页 |
| 文件大小： | 828K |
| 代理商： | PKL4110PIPTSP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页当前第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页
2
EN/LZT 146 047 R4A Ericsson Power Modules, June 2004
PKL 4000 Series Datasheet
Characteristics
Conditions
min
typ
max
Unit
VI
Input voltage range 1)
36
75
Vdc
VIoff
Turn-off input voltage
Ramping from higher
voltage
30
32.5
35
Vdc
VIon
Turn-on input voltage
Ramping from lower
voltage
32
34.4
36
Vdc
CI
Input capacitance
2.18
F
IIac
Reected ripple current
5 Hz to 20 MHz,
VI = 53 V
10
Ap-p
PII
Input idling power
Io= 0, VI = 53 V
4.14
4.46
W
PRC
Input standby power
(turned off with RC)
VI = 53 V, RC activated
0.055
W
Characteristics
min
max
Unit
TC
Operating Case Temperature PKL
PKL4118B PIT
-40
+100
+110
C
TS
Storage temperature
-40
+125
C
VI
Input voltage
-0.5
+80
Vdc
VISO
Isolation voltage (input to output test voltage)
1500
Vdc
Vtr
Input over voltage condition (100 ms)
100
Vdc
VRC
Remote Control Voltage, pin 2
-0.5
15
Vdc
Vadj
Maximum input, pin 6. (measured from pin 1)
-0.5
2xVo
Vdc
Input TC <TC max unless otherwise specied
Note:
Stress in excess of Absolute Maximum Ratings may cause permanent damage. Absolute Maximum Ratings, sometimes referred to as
no destruction limits, are normally tested with one parameter at a time exceeding the limits of Output data or Electrical Characteristics. If
exposed to stress above these limits, function and performance may degrade in an unspecied manner.
Absolute Maximum Ratings
Characteristics
Random Vibration
IEC 68-2-34Ed
Frequency
Spectral density
Duration
10 ... 500 Hz
0.025 g2/Hz
10 min each direction
Sinusoidal
Vibration
IEC 68-2-6 Fc
Frequency
Amplitude
Acceleration
Number of cycles
10 ... 500 Hz
0.75 mm
10 g
10 in each axis
Shock
(half sinus)
IEC 68-2-27 Ea
Peak acceleration
Duration
100 g
6 ms
Temperature
change
IEC 68-2-14 Na
Temperature
Number of cycles
-40 ... +100 C
300
Heat/Humidity
IEC 68-2-3 Ca
Temperature
Humidity
Duration
+85 C
85 % RH
1000 hours
Solder heat
stability
IEC 68-2-20 1A
Temperature, solder
Duration
260 C
10 ...13 s
Resistance to
cleaning solvents
IEC 68-2-45 XA
Method 2
Water
Isopropyl alcohol
Glycol ether
+55 ±5 C
+35 ±5 C
Cold (in operation)
IEC 68-2-1 Ad
Temperature
Duration
-45 C
2 h
Storage test
IEC 68-2-2 Ba
Temperature
Duration
+125 C
1000 h
Environmental Characteristics
Safety
The PKL 4000 series DC/DC converters
are designed in accordance with safety
standards IEC/EN/UL 60 950, Safety of
Information Technology Equipment.
The PKL 4000 series DC/DC converters
are UL 60 950 recognized and certified
in accordance with EN 60 950.
The DC/DC converter should be
installed in the end-use equipment, in
accordance with the requirements of the
ultimate application. The input source
must be isolated by minimum Basic
Insulation from the primary circuit in
accordance with IEC/EN/UL 60 950.
If the input voltage to the DC/DC
converter is 75 V dc or less, then the
output remains SELV (Safety Extra Low
Voltage) under normal and abnormal
operating conditions. Single fault
testing in the input power supply circuit
should be performed with the DC/DC
converter connected to demonstrate that
the input voltage does not exceed 75 V
dc. If the input power source circuit is
a DC power system, the source may be
treated as a TNV2 circuit and testing
has demonstrated compliance with
SELV limits and isolation requirements
equivalent to Basic Insulation in
accordance with IEC/EN/UL 60 950.
It is recommended that a fast blow fuse
with a rating twice the maximum input
current per selected product be used at
the input of each DC/DC converter. If a
fault occurs in the converter that imposes
a short circuit on the input source, this
fuse will provide the following functions:
Isolate the faulty DC/DC converter
from the input power source not to
affect the operation of other parts of
the system.
Protect the distribution wiring from
excessive current and power loss thus
preventing hazardous overheating.
The galvanic isolation is verified in an
electric strength test. The test voltage
(VISO) between input and output is 1500
Vdc for 60 seconds. Leakage current is
less than 1
A at nominal input voltage.
The flammability rating for all
construction parts of the DC/DC
converter meets UL 94V-0.
相关PDF资料 |
PDF描述 |
|---|---|
| PKL4213PIPTLB | 1-OUTPUT 240 W DC-DC REG PWR SUPPLY MODULE |
| PKL4119APIPTM | 1-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE |
| PKL4211PIPTLA | 1-OUTPUT 250 W DC-DC REG PWR SUPPLY MODULE |
| PKL4119PIPTLC | 1-OUTPUT 125 W DC-DC REG PWR SUPPLY MODULE |
| PKL4119PIPT | 1-OUTPUT 125 W DC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PKL4110PIT | 功能描述:DC/DC转换器 3.3 Vdc 50A Iso Input 36-75V 165W RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| PKL4110PITLA | 制造商:Ericsson 功能描述:DC/DC PS SGL-OUT 3.3V 50A 165W - Bulk 制造商:Ericsson 功能描述:Ericsson PKL4110PITLA DC to DC |
| PKL4118APIT | 功能描述:DC/DC转换器 1.8 Vdc 100A Iso Input 36-75V 180W RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| PKL4118APIT REV2 | 制造商:Ericsson 功能描述:Ericsson PKL4118APIT REV2 DC to DC |
| PKL4118APIT/B | 制造商:Ericsson 功能描述:DC/DC PS SGL-OUT 1.8V 100A 180W 11PIN HALF-BRICK - Bulk |
发布紧急采购，3分钟左右您将得到回复。