- 您现在的位置：买卖IC网 > PDF目录69052 > PKL4316APITM (ERICSSON POWER MODULES AB) 1-OUTPUT 366 W DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | PKL4316APITM |
| 厂商： | ERICSSON POWER MODULES AB |
| 元件分类： | 电源模块 |
| 英文描述： | 1-OUTPUT 366 W DC-DC REG PWR SUPPLY MODULE |
| 封装： | 61.50 X 61 MM, 12.70 MM HEIGHT, HALF BRICK PACKAGE-11 |
| 文件页数： | 8/15页 |
| 文件大小： | 226K |
| 代理商： | PKL4316APITM |
2
PKL 4316 Series
EN/LZT 146 039 R1A Ericsson Power Modules, November 2003
Characteristics
Conditions
min
typ
max
Unit
VI
Input voltage range 1)
36
75
Vdc
VIoff
Turn-off input voltage
Ramping from higher
voltage
32
34
Vdc
VIon
Turn-on input voltage
Ramping from lower
voltage
34
36
Vdc
CI
Input capacitance
3.5
F
IIac
Reected ripple current
5 Hz to 20 MHz,
VI = 53 V
5Ap-p
PII
Input idling power
Io= 0, VI = 53 V
6
W
PRC
Input standby power
(turned off with RC)
VI = 53 V, RC activated
0.4
0.6
W
Characteristics
min
max
Unit
TC
Maximum Operating Case Temperature
-40
+110
C
TS
Storage temperature
-40
+125
C
VI
Input voltage
-0.5
+80
Vdc
VISO
Isolation voltage (input to output test voltage)
1500
Vdc
Vtr
Input over voltage condition (100 ms)
100
Vdc
VRC
Remote Control Voltage
12
Vdc
Vadj
Maximum input
10
Vdc
Input TC <TC max unless otherwise specied
Note:
Stress in excess of Absolute Maximum Ratings may cause permanent damage. Absolute Maximum Ratings, sometimes referred to as
no destruction limits, are normally tested with one parameter at a time exceeding the limits of Output data or Electrical Characteristics. If
exposed to stress above these limits, function and performance may degrade in an unspecied manner.
Absolute Maximum Ratings
Characteristics
Random Vibration
IEC 68-2-34Ed
Frequency
Spectral density
Duration
10 ... 500 Hz
0.07 g2/Hz
10 min each direction
Sinusoidal
Vibration
IEC 68-2-6 Fc
Frequency
Amplitude
Acceleration
Number of cycles
10 ... 500 Hz
0.75 mm
10 g
10 in each axis
Shock
(half sinus)
IEC 68-2-27 Ea
Peak acceleration
Duration
100 g
6 ms
Temperature
change
IEC 68-2-14 Na
Temperature
Number of cycles
-40 ... +100 C
300
Heat/Humidity
IEC 68-2-3 Ca
Temperature
Humidity
Duration
+85 C
85 % RH
1000 hours
Solder heat
stability
IEC 68-2-20 1A
Temperature, solder
Duration
260 C
10 ...13 s
Resistance to
cleaning solvents
IEC 68-2-45 XA
Method 2
Water
Isopropyl alcohol
Glycol ether
+55 ±5 C
+35 ±5 C
Cold (in operation)
IEC 68-2-1 Ad
Temperature
Duration
-45 C
2 h
Storage test
IEC 68-2-2 Ba
Temperature
Duration
+125 C
1000 h
Environmental Characteristics
Safety
The PKL 4000 series DC/DC converters
are designed in accordance with safety
standards IEC/EN/UL 60 950, Safety of
Information Technology Equipment. The
PKL 4000 series DC/DC converters are
UL 60 950 recognized and certied in
accordance with EN 60 950.
The DC/DC converter should be installed
in the end-use equipment, in accordance
with the requirements of the ultimate
application. The input source must be
isolated by minimum Basic insulation
from the primary circuit in accordance
with IEC/EN/UL 60 950. If the input
voltage to the DC/DC converter is 75 V
dc or less, then the output remains SELV
(Safety Extra Low Voltage) under normal
and abnormal operating conditions.
Single fault testing in the input power
supply circuit should be performed
with the DC/DC converter connected to
demonstrate that the input voltage does
not exceed 75 V dc. If the input power
source circuit is a DC power system,
the source may be treated as a TNV2
circuit and testing has demonstrated
compliance with SELV limits and
isolation requirements equivalent to Basic
insulation in accordance with
IEC/EN/UL 60 950.
It is recommended that a fast blow fuse
with a rating twice the maximum input
current per selected product be used at
the input of each DC/DC converter. If a
fault occurs in the converter that imposes
a short circuit on the input source, this
fuse will provide the following functions:
Isolate the faulty DC/DC converter
from the input power source not to
affect the operation of other parts of
the system.
Protect the distribution wiring from
excessive current and power loss thus
preventing hazardous overheating.
The galvanic isolation is veried in an
electric strength test.
The test voltage
(VISO) between input and output is 1500
Vdc for 60 seconds. Leakage current is less
than 1uA at nominal input voltage.
The ammability rating for all
construction parts of the DC/DC
converter meets UL 94V-0.
相关PDF资料 |
PDF描述 |
|---|---|
| PKL4316APIT | 1-OUTPUT 366 W DC-DC REG PWR SUPPLY MODULE |
| PKM2513EPIPHS | 1-OUTPUT 50 W DC-DC REG PWR SUPPLY MODULE |
| PKM2513EPIHSLA | 1-OUTPUT 50 W DC-DC REG PWR SUPPLY MODULE |
| PKM2511EPIPLA | 1-OUTPUT 50 W DC-DC REG PWR SUPPLY MODULE |
| PKM2511EPIP | 1-OUTPUT 50 W DC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PKL4316PIT | 制造商:Ericsson 功能描述:DC/DC PS SGL-OUT 28V 11A 310W - Bulk |
| PKL4316PITM | 制造商:Ericsson 功能描述:DC/DC PS SGL-OUT 28V 11A 310W - Bulk |
| PKL46-1 | 制造商:Thomas & Betts 功能描述:Pin Terminal (2/0)AWG M 152.4mm Tin |
| PKL4918PIOA | 制造商:Ericsson 功能描述:EXTENDED 1/2 BRICK "DOUBLE P" SERIES, THRU-HOLE, CONVERTER - Bulk |
| PKL4918PIT | 制造商:Ericsson 功能描述:DC/DC PS SGL-OUT 1.8V 50A 90W - Bulk |
发布紧急采购，3分钟左右您将得到回复。