- 您现在的位置：买卖IC网 > PDF目录69056 > PKM4318HEPI (ERICSSON POWER MODULES AB) 1-OUTPUT 30 W DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | PKM4318HEPI |
| 厂商： | ERICSSON POWER MODULES AB |
| 元件分类： | 电源模块 |
| 英文描述： | 1-OUTPUT 30 W DC-DC REG PWR SUPPLY MODULE |
| 封装： | ROHS COMPLIANT, QUARTER BRICK, 8 PIN |
| 文件页数： | 27/37页 |
| 文件大小： | 2036K |
| 代理商： | PKM4318HEPI |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页
EN/LZT 146 051 R7A Ericsson Power Modules, February 2007
PKM 4000E PI Datasheet
Operating Information
Input Voltage
The input voltage range 36…75Vdc meets the requirements
of the European Telecom Standard ETS 300 132-2 for
normal input voltage range in –48V and –60V DC systems,
-40 .5…-57 .0V and –50 .0…-72V respectively. At input
voltages exceeding 75V, the power loss will be higher than
at normal input voltage and TPcb must be limited to absolute
max +110°C . The absolute maximum continuous input
voltage is 80Vdc .
Turn-Off Input Voltage
The PKM 4000E Series DC/DC converters monitor the input
voltage and will turn on and turn off at predetermined levels .
The minimum hysteresis between turn on and turn off input
voltage is 2V where the turn on input voltage is the highest .
Output Voltage Adjust (Vadj)
All PKM 4000E Series DC/DC converters have an Output
Voltage adjust pin (Vadj) . This pin can be used to adjust
the output voltage above or below Output voltage initial
setting . When increasing the output voltage, the voltage at
the output pins (including any remote sense offset) must
be kept below the overvoltage trip point, to prevent the
converter from shut down . Also note that at increased output
voltages the maximum power rating of the converter remains
the same, and the output current capability will decrease
correspondingly. To decrease the output voltage the resistor
should be connected between Vadj pin and –Sense pin .
To increase the voltage the resistor should be connected
between Vadj pin and +Sense pin . The resistor value of the
Output voltage adjust function is according to information
given under the output section .
Remote Control (RC)
All PKM 4000E Series DC/DC converters have remote sense
that can be used to compensate for moderate amounts of
resistance in the distribution system and allow for voltage
regulation at the load or other selected point . The remote
sense lines will carry very little current and do not need a
large cross sectional area . However, the sense lines on the
PCB should be located close to a ground trace or ground
plane . In a discrete wiring situation, the use of twisted pair
wires or other technique to reduce noise susceptibility
is highly recommended . The remote sense circuitry will
compensate for up to 10% voltage drop between the sense
voltage and the voltage at the output pins . The output
voltage and the remote sense voltage offset must be less
than the minimum over voltage trip point . If the remote sense
is not needed the –Sense should be connected to –Out and
+Sense should be connected to +Out .
Remote Sense
Circuit configuration for output voltage adjust
+Out
-Out
+Sense
Vadj
-Sense
Load
Radj
Decrease
Load
Increase
+Out
-Out
+Sense
Vadj
-Sense
The PKM 4000E Series DC/DC
converters have a remote control
function referenced to the primary
side (- In), with negative and positive
logic options available . The RC
function allows the converter to be
turned on/off by an external device
like a semiconductor or mechanical
switch . The RC pin has an internal
pull up resistor to + In . The needed maximum sink current
is 1mA . When the RC pin is left open, the voltage generated
on the RC pin is 3 .5 - 6 V. The maximum allowable leakage
current of the switch is 50 A .
The standard converter is provided with “negative logic”
remote control and the converter will be off until the RC
pin is connected to the - In . To turn on the converter the
voltage between RC pin and - In should be less than 1V.
To turn off the converter the RC pin should be left open, or
connected to a voltage higher than 4 V referenced to - In . In
situations where it is desired to have the converter to power
up automatically without the need for control signals or a
switch, the RC pin can be wired directly to - In .
The second option is “positive logic” remote control, which
can be ordered by adding the suffix “P” to the end of the
part number. The converter will turn on when the input
voltage is applied with the RC pin open . Turn off is achieved
by connecting the RC pin to the - In . To ensure safe turn
off the voltage difference between RC pin and the - In pin
shall be less than 1V. The converter will restart automatically
when this connection is opened .
Circuit configuration
for RC function
+In
RC
-In
相关PDF资料 |
PDF描述 |
|---|---|
| PKM4218LEPIHS | 1-OUTPUT 24 W DC-DC REG PWR SUPPLY MODULE |
| PKM4510EPIHS | 1-OUTPUT 50 W DC-DC REG PWR SUPPLY MODULE |
| PKM4511EPI | 1-OUTPUT 50 W DC-DC REG PWR SUPPLY MODULE |
| PKM4218LEPILA | 1-OUTPUT 24 W DC-DC REG PWR SUPPLY MODULE |
| PKM4513EPIHS | 1-OUTPUT 50 W DC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PKM4318PI | 功能描述:DC/DC转换器 1.8 Vdc 20A Iso Input 36-75V 36W RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| PKM4318PI0A | 制造商:ERICSSON 功能描述: |
| PKM4318PIOA | 功能描述:DC/DC转换器 1.5 Vdc 20A Iso Input 36-75V 30W RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| PKM4319EPI | 功能描述:DC/DC转换器 2.5 Vdc 15A Iso Input 36-75V 38W RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| PKM4402NGPI | 功能描述:DC/DC转换器 9.6Vdc 63A Isolated Input 36-55V 480W RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
发布紧急采购，3分钟左右您将得到回复。