3
PM100CLA060
Intellimod L-Series
Three Phase IGBT Inverter
100Amperes/600 Volts
Powerex, Inc., 200 E. Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272
Electrical and Mechanical Characteristics, Tj = 25°C unless otherwise specied
Characteristics
Symbol
Test Conditions
Min.
Typ.
Max.
Units
Control Sector
Short Circuit Trip Level
SC
-20°C ≤ Tj ≤ 125°C, VD = 15V
200
—
Amperes
Short Circuit Current Delay Time
toff(SC)
VD = 15V
—
0.2
—
s
Over Temperature Protection
OT
Trip Level
135
145
155
°C
(Detect Tj of IGBT Chip)
OTR
Reset Level
—
125
—
°C
Supply Circuit Under-voltage Protection
UV
Trip Level
11.5
12.0
12.5
Volts
(-20 ≤ Tj ≤ 125°C)
UVR
Reset Level
—
12.5
—
Volts
Circuit Current
ID
VD = 15V, VCIN = 15V, VN1-VNC
—
20
30
mA
VD = 15V, VCIN = 15V, VXP1-VXPC
—
5
10
mA
Input ON Threshold Voltage
Vth(on)
Applied between UP-VUPC,
1.2
1.5
1.8
Volts
Input OFF Threshold Voltage
Vth(off)
VP-VVPC, WP-VWPC, UN- VN- WN-VNC 1.7
2.0
2.3
Volts
Fault Output Current*
IFO(H)
VD = 15V, VCIN = 15V
—
0.01
mA
IFO(L)
VD = 15V, VCIN = 15V
—
10
15
mA
Fault Output Pulse Width*
tFO
VD = 15V
1.0
1.8
—
ms
*Fault output is given only when the internal SC, OT and UV protections schemes of either upper or lower devide operate to protect it.
Thermal Characteristics
Characteristic
Symbol
Condition
Min.
Typ.
Max.
Units
Junction to Case Thermal Resistance
Rth(j-c)Q
IGBT (Per 1/6 Module) (Note 1)
—
0.35
°C/Watt
Rth(j-c)D
FWDi (Per 1/6 Module) (Note 1)
—
0.56
°C/Watt
Rth(j-c)Q
IGBT (Per 1/6 Module) (Note 2)
—
0.27
°C/Watt
Rth(j-c)D
FWDi (Per 1/6 Module) (Note 2)
—
0.43
°C/Watt
Contact Thermal Resistance
Rth(c-f)
Case to Fin Per Module,
—
0.038
°C/Watt
Thermal Grease Applied (Note 1)
Recommended Conditions for Use
Characteristic
Symbol
Condition
Value
Units
Supply Voltage
VCC
Applied across P-N Terminals
≤400
Volts
Control Supply Voltage**
VD
Applied between VUP1-VUPC,
15.0 ± 1.5
Volts
VVP1-VVPC, VWP1-VWPC, VN1-VNC
Input ON Voltage
VCIN(on)
Applied between UP-VUPC,
≤0.8
Volts
Input OFF Voltage
VCIN(off)
VP-VVPC, WP-VWPC, UN- VN- WN-VNC
≥9.0
Volts
PWM Input Frequency
fPWM
—
≤20
kHz
Arm Shoot-through Blocking Time
tDEAD
Input Signal
≥2.0
s
** With ripple satisfying the following conditions: dv/dt swing ≤ ±5V/s, Variation ≤ 2V peak to peak.
Arm
UP
VP
WP
UN
VN
WN
Axis
IGBT FWDi IGBT FWDi IGBT FWDi IGBT FWDi IGBT FWDi IGBT FWDi
X
28.3
28.0
65.0
65.2
87.0
87.2
39.3
39.5
54.0
53.7
76.0
75.7
Y
-8.5
1.7
-8.5
1.7
-8.5
1.7
6.5
-5.2
6.5
-5.2
6.5
-5.2
Note 2: TC (under the chip) Measurement Point
Y
BOTTOM VIEW
X
TOP VIEW
TC
MEASUREMENT
POINT
Note 1:TC (base plate) Measurement Point