
PM50B6L1C060
Photo Voltaic IPM
H-Bridge + 2 Choppers
50 Amperes/600 Volts
Powerex, Inc., 173 Pavilion Lane,Youngwood, Pennsylvania 15697 (724) 925-7272 www.pwrx.com
4
03/11 Rev. 0
Electrical and Mechanical Characteristics,
Tj = 25°C unless otherwise specified
Characteristics
Symbol
Test Conditions
Min.
Typ.
Max.
Units
Control Part
Circuit Current
ID
VD = 15V, VCIN = 15V, VN1-VNC
—
6.5
12
mA
VD = 15V, VCIN = 15V, V*P1-V*PC
—
1.6
4
mA
Input ON Threshold Voltage
Vth(on)
Applied between UP-VUPC,
1.2
1.5
1.8
Volts
Input OFF Threshold Voltage
Vth(off)
VP-VVPC, UN- VN- WN-Br-VNC
1.7
2.0
2.3
Volts
Short Circuit Trip Level
SC
-20°C ≤ Tj ≤ 125°C, VD = 15V
75
—
Amperes
Short Circuit Current Delay Time
toff(SC)
VD = 15V
—
0.2
—
s
Over Temperature Protection
OT
Trip Level
135
—
°C
(Detect Temperature of IGBT)
OT(hys)
Hysteresis
—
20
—
°C
Supply Circuit Under-voltage Protection
UVt
Trip Level
11.5
12.0
12.5
Volts
(-20°C ≤ Tj ≤ 125°C)
UVr
Reset Level
—
12.5
—
Volts
Fault Output Current*2
IFO(H)
VD = 15V, VFO = 15V
—
0.01
mA
IFO(L)
VD = 15V, VFO = 15V
—
10
15
mA
Fault Output Pulse Width*2
tFO
VD = 15V
1.0
1.8
—
ms
Thermal Characteristics,
Tj = 25°C unless otherwise specified
Characteristic
Symbol
Condition
Min.
Typ.
Max.
Units
Junction to Case Thermal Resistance
Rth(j-c)Q
Inverter IGBT (Per 1 Element)*1
—
0.74
°C/Watt
Rth(j-c)D
Inverter FWDi (Per 1 Element)*1
—
1.28
°C/Watt
Rth(j-c)Q
Converter IGBT (Per 1 Element)*1
—
0.74
°C/Watt
Rth(j-c)D
Converter FWDi (Per 1 Element)*1
—
1.28
°C/Watt
Rth(j-c)D
Converter Diode (Per 1 Element)*1
—
1.28
°C/Watt
Contact Thermal Resistance
Rth(c-f)
Case to Fin (Per 1 Element)*1,
—
0.060
—
°C/Watt
Thermal Grease Applied
Recommended Conditions for Use
Characteristic
Symbol
Condition
Value
Units
Inverter Supply Voltage
VCC
Applied across P-N Terminals
≤450
Volts
Control Supply Voltage*3
VD
Applied between VUP1-VUPC,
15.0 ± 1.5
Volts
VVP1-VVPC, VN1-VNC
Input ON Voltage
VCIN(on)
Applied between UP-VUPC,
≤0.8
Volts
Input OFF Voltage
VCIN(off)
VP-VVPC, UN- VN- WN-Br-VNC
≥9.0
Volts
PWM Input Frequency
fPWM
Using Application Circuit Input Signal of IPM,
≤20
kHz
3-Phase Sinusoidal PWM VVVF Inverter
Arm Shoot-through Blocking Time
tDEAD
For IPMs Each Input Signals
≥2.0
s
*1 When using this value, Rth(s-a) should be measured just under the chips.
*2 Fault output is given only when the internal SC, OT and UV protections schemes of either upper or lower devide operate to protect it.
Fault output of SC protection given pulse. Fault output of OT, UV protection given pulse while over trip level.
*3 With ripple satisfying the following conditions: dv/dt swing ≤5V/s ; variation ≤2V peak-to-peak.