参数资料
型号: PMA4118HSF/B
厂商: ERICSSON POWER MODULES AB
元件分类: 电源模块
英文描述: 1-OUTPUT 18 W DC-DC REG PWR SUPPLY MODULE
封装: SMT-14
文件页数: 11/21页
文件大小: 363K
代理商: PMA4118HSF/B
19
PMA 4000 Series Datasheet
EN/LZT 146 012 R3A Ericsson Power Modules, November 2003
Miscellaneous
The PMA 4000 series DC/DC regulators are intended for
reflow soldering processes. Extra precautions must be taken
when reflow-soldering the module. Neglecting the soldering
information provided may result in permanent damage or
significant degradation of the regulator performance. No
responsibility is assumed if these recommendations are not
strictly followed.
The regulator may be reflow soldered using vapour phase
reflow (VPR) or forced convection reflow processes. The
high thermal mass of the component and its effect on the
temperature differences (
T) over a PCB means that particular
attention should be paid to other temperature sensitive
components.
For successful soldering of the PMA 4000 series DC/DC
regulators, both pin temperature and case temperature must be
monitored:
Minimum temperature of the pins:
to ensure reliable solder joints
Maximum temperature of the regulator case:
to avoid overheating
Soldering Information
Minimum temperature:
Most important is to ensure that the pins on the coolest side
reach sufcient soldering temperature for a sufcient time.
Therefore, the pin temperature measurements should be done
on both sides of the module, preferrably on the middle pins
(3/4 and 11/12).
The pins of the module are palladium plated. In order to
guarantee a reliable solder joint, a pin temperature (TP) in
excess of the solder fusing temperatue (183C for Sn/Pb 63/37)
for 25 seconds, and a peak temperature above 195C should be
reached.
Maximum temperature:
To avoid damage to the module, the reow prole should
be optimised to avoid overheating. The case temperature
(TC) should be monitored with a thermocouple attached to
the center of the top of the case using an adhesive or heat
conductive paste.
A sufciently extended soak time is recommended to ensure
an even temperature throughout the PCB, for both small
and large components. To reduce the risk of overheating the
module it is also recommended to minimise the time in reow
as much as possible.
Conventional Sn-Pb convection solder process
For conventional Sn-Pb solder processes, the PMA 4000 series
regulator is qualied for MSL 1 according to Jedec standard
(J-STD-020b July 2002).
During reow, the case temperature must not exceed 215C at
any time.
0
70
140
210
280
350
0
50
100
150
200
250
300
[°C]
Time
reflow ramp-
up max 3°/s
cooling
max 5°/s
preheat
max 3°/s
soak zone (150°C-
180°C) 30-180s
reflow
zone
max case temperature
@ 215°C (Sn-Pb solders)
pin temperature
case temperature
相关PDF资料
PDF描述
PMA4118LSF 1-OUTPUT 14.4 W DC-DC REG PWR SUPPLY MODULE
PMA4218GSF 1-OUTPUT 21.6 W DC-DC REG PWR SUPPLY MODULE
PMA5319SF/C 1-OUTPUT 30 W DC-DC REG PWR SUPPLY MODULE
PMA5310SF/B 1-OUTPUT 39.6 W DC-DC REG PWR SUPPLY MODULE
PMA5310SF/C 1-OUTPUT 39.6 W DC-DC REG PWR SUPPLY MODULE
相关代理商/技术参数
参数描述
PMA5100DEMOBOARD 制造商:Infineon Technologies AG 功能描述:
PMA5105 功能描述:射频收发器 10bit ADC 125kHz ASK LF Receiver RoHS:否 制造商:Atmel 频率范围:2322 MHz to 2527 MHz 最大数据速率:2000 Kbps 调制格式:OQPSK 输出功率:4 dBm 类型: 工作电源电压:1.8 V to 3.6 V 最大工作温度:+ 85 C 接口类型:SPI 封装 / 箱体:QFN-32 封装:Tray
PMA5105XUMA1 制造商:Infineon Technologies AG 功能描述:MCU 8-Bit 8051 CISC 6KB Flash 2.5V/3.3V 38-Pin TSSOP T/R 制造商:Infineon Technologies AG 功能描述:CONTROL - Tape and Reel 制造商:Infineon Technologies AG 功能描述:IC MCU/TX/ADC/LF TXRX 38-TSSOP
PMA5110 功能描述:射频收发器 10bit ADC 125kHz ASK LF Receiver RoHS:否 制造商:Atmel 频率范围:2322 MHz to 2527 MHz 最大数据速率:2000 Kbps 调制格式:OQPSK 输出功率:4 dBm 类型: 工作电源电压:1.8 V to 3.6 V 最大工作温度:+ 85 C 接口类型:SPI 封装 / 箱体:QFN-32 封装:Tray
PMA51104345BOARDTOBO1 制造商:Infineon Technologies AG 功能描述:BOARD - Boxed Product (Development Kits)