- 您现在的位置：买卖IC网 > Datasheet目录352 > PRD48BH480T200A00 (Vicor Corporation)HALF-CHIP REGULATOR EVAL BOARD Datasheet资料下载
参数资料
| 型号： | PRD48BH480T200A00 |
| 厂商： | Vicor Corporation |
| 文件页数： | 4/19页 |
| 文件大小： | 0K |
| 描述： | HALF-CHIP REGULATOR EVAL BOARD |
| 标准包装： | 1 |
| 系列： | V-I Chip™, PRM™ |
| 主要目的： | DC/DC，步升/步降 |
| 输出及类型： | 1，非隔离 |
| 功率 - 输出： | 200W |
| 输出电压： | 5 ~ 55 V |
| 电流 - 输出： | 4.17A |
| 输入电压： | 8 ~ 55 V |
| 稳压器拓扑结构： | 降压-升压 |
| 频率 - 开关： | 1MHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | PRM48BH480T200A |
| 其它名称： | 1102-1193 PRD48BH480T200A00-ND |
12. Output Voltage Trim Pot (R 22 ): 11 turn trim pot adjusts the output voltage by increasing or
decreasing the error amplifier reference voltage (V REF ). Turn clockwise to increase the output
voltage, and counterclockwise to decrease the output voltage. Adjustment slot is
1.5 mm (L) x 0.6 mm (W).
13. High Side Current Sense Circuit (R 08 , Q 02 ): Current sense shunt and IC monitor the output
current and provide feedback to the IF pin for current limit protection. Gain is typically 400
mV/A, and is set for appropriate current limit set point. IF signal can be monitored at the
Signal Test Point Header (#6) to provide approximate output current measurement, but should
not be used if accurate output current measurements are required (<10% error). Efficiency
measurements should always be performed using an external calibrated shunt.
14. Output Inductor (L01): 0.4 uH inductor provides high AC impedance between PRM ? and VTM ?
(when used) to prevent high- frequency switching currents from circulating between devices.
15. Voltage Sense and Error Amplifier (U09A, U09B): Dual op amp provides voltage sensing and
error amplifier function. The customer board is nominally configured for local voltage sensing
at the PRM output. U09B can be re-configured as a differential amplifier to allow for
non-isolated remote sensing at the VTM output or load. This requires rework as described in
Section 8.3.
16. Push Pin Heat Sink and Grounding Clip Mounting Holes: Use these holes for installing the
optional push pin heat sink and grounding clips included with the board.
Use of a heat sink is highly recommended for appropriate cooling of the PRM.
3.2 Test Points
In addition to the Signal Test Point Headers (#6, #7), there are a number of surface mount test
points on the board with the following functions.
1. V IN+ , V IN- (TP01, TP03): Input voltage test points provide Kelvin connections to the input
leads. Use these test points for measuring the input voltage to avoid error due to interconnect
losses.
2. V OUT+ , V OUT- (TP04, TP05): Output voltage test points provide Kelvin connections to the
output leads. Use these test points for measuring the output voltage to avoid error due to
interconnect losses.
3. Signal Ground (TP01): Signal Ground (SG) test point is the ground reference for all control
circuitry.
4. VS+, VS- (TP10, TP11): +/- sense inputs to the differential amplifier when remote sense is
implemented. When used with a VTM Customer Board, the sense leads may be wired to the
VTM output voltage through X03 depending on which VTM board is used. If not, a twisted
pair of wires can be used to connect sense leads to the VTM board output from these test
points.
UG:008
vicorpower.com
Applications Engineering: 800 927.9474
Page 4
相关PDF资料 |
PDF描述 |
|---|---|
| PRM-14464 | BOX RACKMOUNT 5.25"X 8" PLASTIC |
| PS-415-HGULTRA | POWER STRIP 15A 4OUT 15'CORD |
| PS-415-HG | POWER STRIP 8.65 15A 4OUT 15' |
| PS-602-HG | POWER STRIP 120V 6OUT HOSP 1.5' |
| PS-606-HG | POWER STRIP 13.75" 6OUT 6'COR |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PRD48BH480T200B00 | 功能描述:PRM48BH480T200B00 VI Chip? PRM? DC/DC, Step Up or Down 1, Non-Isolated Outputs Evaluation Board 制造商:vicor corporation 系列:VI Chip? PRM? 零件状态:有效 主要用途:DC/DC，步升/步降 输出和类型:1，非隔离 功率 - 输出:200W 电压 - 输出:48V 电流 - 输出:4.17A 电压 - 输入:38 V ~ 55 V 稳压器拓扑:降压-升压 频率 - 开关:1MHz 板类型:完全填充 所含物品:板 使用的 IC/零件:PRM48BH480T200B00 标准包装:1 |
| PRD-4AG0-240 | 功能描述:RELAY GENERAL PURPOSE 30A 240V RoHS:是 类别:继电器 >> 功率，高于 2 安 系列:PRD 其它有关文件:Standards Chart 标准包装:50 系列:DK 继电器类型:通用 线圈类型:无锁存 线圈电流:16.7mA 线圈电压:12VDC 触点形式:SPST-NO（1 A 型） 触点额定值（电流）:10A 切换电压:250VAC，125VDC - 最小值 关闭电压（最大）:8.4 VDC 关闭电压（最小）:1.2 VDC 特点:密封式 - 全部 安装类型:通孔 端接类型:PC 引脚 包装:管件 触点材料:银锡氧化物（AgSnO） 操作时间:10ms 释放时间:8ms 线圈功率:200 mW 线圈电阻:720 欧姆 工作温度:-40°C ~ 65°C 其它名称:255-1096DK1AE-12V |
| PRD-4AY0-120 | 制造商:TE Connectivity 功能描述: |
| PRD-4AY0-24 | 制造商:TE Connectivity 功能描述: |
| PRD-4DG0-24 | 制造商:TE Connectivity 功能描述: |
发布紧急采购，3分钟左右您将得到回复。