- 您现在的位置：买卖IC网 > PDF目录97636 > PS21562-SP AC MOTOR CONTROLLER, 10 A, XMA37 PDF资料下载
参数资料
| 型号： | PS21562-SP |
| 元件分类： | 运动控制电子 |
| 英文描述： | AC MOTOR CONTROLLER, 10 A, XMA37 |
| 封装： | DIP-37 |
| 文件页数： | 8/8页 |
| 文件大小： | 122K |
| 代理商： | PS21562-SP |
MITSUBISHI SEMICONDUCTOR <Dual-In-Line Package Intelligent Power Module>
PS21562-SP
TRANSFER-MOLD TYPE
INSULATED TYPE
Jul. 2005
Fig. 6 TYPICAL DIP-IPM APPLICATION CIRCUIT EXAMPLE
Note 1 : To prevent the input signals oscillation, the wiring of each input should be as short as possible. (Less than 2cm)
2: By virtue of integrating an application specific type HVIC inside the module, direct coupling to MCU terminals without any opto-coupler
or transformer isolation is possible.
3: FO output is open drain type. This signal line should be pulled up to the positive side of the 5V power supply with approximately 10k
resistor.
4: FO output pulse width is determined by the external capacitor between CFO and VNC terminals (CFO). (Example : CFO = 22 nF
→ tFO = 1.8 ms (typ.))
5: The logic of input signal is high-active. The DIP-IPM input signal section integrates a 2.5k
(min) pull-down resistor. Therefore, when
using external filtering resistor, care must be taken to satisfy the turn-on threshold voltage requirement.
6: To prevent malfunction of protection, the wiring of A, B, C should be as short as possible.
7: Please set the C5R1 time constant in the range 1.5~2
s.
8: Each capacitor should be located as nearby the pins of the DIP-IPM as possible.
9: To prevent surge destruction, the wiring between the smoothing capacitor and the P, N1 pins should be as short as possible. Approxi-
mately a 0.1~0.22
F snubber capacitor between the P-N1 pins is recommended.
10 : To prevent ICs from surge destruction, it is recommended to insert a Zener diode (24V, 1W) between each control supply terminals.
11 : The reference voltage Vref of comparator should be set up the same rating of short circuit trip level (Vsc(ref): min.0.45V to max.0.52V).
12 : OR logic output level should be set up the same rating of short circuit trip level (Vsc(ref): min.0.45V to max.0.52V).
HO
DIP-IPM
C3
C2
C1
HO
IN
15V line
5V line
IN
COM
UOUT
VOUT
WOUT
VNO
CFO
GND
F
o
WN
VN
VCC
C
A
C4(CFO)
CFO
CIN
VNO
NW
NV
NU
CIN
VS
VB
VCC
Fo
WN
VN
UN
UN
WP
VP
UP
VNC
VN1
VP1
VWFS
VVFS
VUFS
VWFB
VVFB
VUFB
M
C3
HVIC1
HVIC2
HVIC3
LVIC
CONTROLLER
W
V
U
P
Comparator
External protection circuit
Too long wiring here might
cause short-circuit.
C5
R1
B
Vref
+
-
C5
R1
B
Vref
+
-
C5
N1
R1
B
Vref
+
-
Shunt resistors
If this wiring is too long, the SC
level fluctuation might be larger
and cause SC malfunction.
Long GND wiring here might
generate noise to input and cause
IGBT malfunction.
OR Logic
C1:Tight tolerance temp-compensated electrolytic type
C2,C3: 0.22~2
F R-category ceramic capacitor for noise filtering
相关PDF资料 |
PDF描述 |
|---|---|
| PS21562 | AC MOTOR CONTROLLER, 10 A, XMA35 |
| PS21563-P | AC MOTOR CONTROLLER, 20 A, DMA35 |
| PS21867-A | AC MOTOR CONTROLLER, 60 A, QMA41 |
| PS21867 | AC MOTOR CONTROLLER, 60 A, QMA41 |
| PS21962-4S | AC MOTOR CONTROLLER, 10 A, DMA24 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PS21563 | 制造商:POWEREX 制造商全称:Powerex Power Semiconductors 功能描述:Intellimod⑩ Module Dual-In-Line Intelligent Power Module (10 Amperes/600 Volts) |
| PS21563-P | 功能描述:MOD IPM 600V 10A MINI DIP RoHS:是 类别:半导体模块 >> 功率驱动器 系列:Intellimod™ 标准包装:15 系列:SPM® 类型:FET 配置:三相反相器 电流:1.8A 电压:500V 电压 - 隔离:1500Vrms 封装/外壳:23-DIP 模块 |
| PS21563-PP | 制造商:POWEREX 制造商全称:Powerex Power Semiconductors 功能描述:Intellimod? Module Dual-In-Line Intelligent Power Module 10 Amperes/600 Volts |
| PS21563-SP | 功能描述:MOD IPM 600V 10A MINI DIP RoHS:是 类别:半导体模块 >> 功率驱动器 系列:Intellimod™ 标准包装:15 系列:SPM® 类型:FET 配置:三相反相器 电流:1.8A 电压:500V 电压 - 隔离:1500Vrms 封装/外壳:23-DIP 模块 |
| PS21564 | 制造商:POWEREX 制造商全称:Powerex Power Semiconductors 功能描述:Intellimod⑩ Module Dual-In-Line Intelligent Power Module (15 Amperes/600 Volts) |
发布紧急采购，3分钟左右您将得到回复。