- 您现在的位置：买卖IC网 > Datasheet目录633 > PS21767 (Powerex Inc)MOD IPM 600V 30A MINI DIP Datasheet资料下载
参数资料
| 型号： | PS21767 |
| 厂商： | Powerex Inc |
| 文件页数： | 7/9页 |
| 文件大小： | 0K |
| 描述： | MOD IPM 600V 30A MINI DIP |
| 标准包装： | 4 |
| 系列： | Intellimod™ |
| 类型： | IGBT |
| 配置： | 3 相 |
| 电流： | 30A |
| 电压： | 600V |
| 电压 - 隔离： | 2500VDC |
| 封装/外壳： | PCB 模块 |
| 配用： | 835-1028-ND - KIT DEV INTERFACE FOR IPM DIP |
| 其它名称： | 835-1038 |
Powerex, Inc., 173 Pavilion Lane, Youngwood, Pennsylvania 15697 (724) 925-7272
PS21767
Intellimod? Module
Dual-In-Line Intelligent Power Module
30 Amperes/600 Volts
Application Circuit
+3.3 to +5V
+15V
C1
R1 D1
+
C2
DZ1
VUFS
VUFB
P
C7
C6
+
AC LINE
R2
C2
VP1
UP
+VCC
C5
C1
+
C2
VVFS
VVFB
U
R1 D1
DZ1
R2
C2
VP1
VP
+VCC
C5
C1
+
C2
VWFS
VWFB
V
MOTOR
R1 D1
DZ1
R2
C2
VP1
WP
+VCC
C5
R3
R2
VNO
UN
W
RSHUNT
R2
R2
VN
WN
FO
CFO
INPUT SIGNAL
CONDITIONING
FAULT
LOGIC
N(U)
RSHUNT
TO
CONTROLLER
C5 C5 C5 C4
CIN
N(V)
C3
+
C2
VNC
VN1
UV
PROT.
+VCC LVIC
N(W)
RSHUNT
Component Selection:
This symbol indicates
connection to ground plane.
Dsgn.
D1
DZ1
C1
C2
C3
C4
C5
C6
C7
RSHUNT
R1
R2
R3
Typ. Value
1A, 600V
16V, 0.25W
10-100uF, 50V
0.22-2.0uF, 50V
10-100uF, 50V
22nF, 50V
100pF, 50V
200-2000uF, 450V
0.1-0.22uF, 450V
5-100mohm
10 ohm
330 ohm
10k ohm
Description
Boot strap supply diode – Ultra fast recovery
Control and boot strap supply over voltage suppression
Boot strap supply reservoir – Electrolytic, long life, low Impedance, 105°C (Note 5)
Local decoupling/High frequency noise filters – Multilayer ceramic (Note 5)
Control power supply filter – Electrolytic, long life, low Impedance, 105°C (Note 5)
Fault output timer capacitor
Optional Input signal noise filter – Multilayer ceramic (Note 1)
Main DC bus filter capacitor – Electrolytic, long life, high ripple current, 105°C
Surge voltage suppression capacitor – Polyester/Polypropylene film (Note 8)
Current sensing resistor – Non-inductive, temperature stable, tight tolerance (Note 9)
Boot strap supply inrush limiting resistor
Optional control input noise filter (Note 1, Note 2)
Fault output signal pull-up resistor (Note 3)
Notes:
1) Input drive is active-high type. There is a 2.5k (min.) pull-down resistor integrated in the IC input circuit. To prevent malfunction, the wiring
of each input should be as short as possible. When using RC coupling circuit, make sure the input signal level meets the turn-on and turn-off
threshold voltage. See application notes for details.
2) Internal HVIC provides high voltage level shifting allowing direct connection of all six driving signals to the controller.
3) FO output is an open collector type. Pull up resistor (R3) should be adjusted to current sink capability of the controller.
4) To prevent input signal oscillations, minimize wire length to controller (~2cm). Additional RC filtering (C5 etc.) may be required. If filtering is added
be careful to maintain proper dead time and voltage levels. See application notes for details.
5) All capacitors should be mounted as close to the terminals as possible. (C1: good temperature, frequency characteristic electrolytic type,
and C2, C3: good temperature, frequency and DC bias characteristic ceramic type are recommended.)
6) Shows short circuit protection disabled. See application notes for use of short circuit protection.
7) Local decoupling frequency filter capacitors must be connected as close as possible to the module’s pins.
8) The length of the DC link wiring between C5, C6, the DIP’s P terminal and the shunt must be minimized to prevent excessive transient
voltages. In particular C6 should be mounted as close to the DIP as possible.
9) Use high quality, tight tolerance current sensing resistor. Connect resistor as close as possible to the DIP’s N terminal. Be careful to check
for proper power rating. See application notes for calculation of resistance value.
10) Inserting a Zener diode (24V/1W) between each pair of control supply terminals to prevent surge destruction is recommended.
Rev. 07/07
7
相关PDF资料 |
PDF描述 |
|---|---|
| PS21961-4 | MOD IPM 600V 3A SUPERMINI DIP |
| PS21962-4C | MOD IPM 600V 5A SUPERMINIDIP |
| PS21962-4S | MOD IPM 600V 5A SUPERMINIDIP |
| PS21963-4ES | MOD IPM 600V 8A SUPERMINIDIP |
| PS21963-4E | MOD IPM 600V 8A SUPERMINIDIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PS21767-V | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:Dual-In-Line Package Intelligent Power Module |
| PS218 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
| PS21864-P | 制造商:Mitsubishi Electric 功能描述:POWER IPM TRANSISTOR |
| PS21865-P | 制造商:Powerex Power Semiconductors 功能描述:INTELLIGENT POWER MODULE, 600V, 20A, DIP, Transistor Polarity:(Not Available), D |
| PS21867 | 制造商:Powerex Power Semiconductors 功能描述:POWER IPM TRANSISTOR |
发布紧急采购，3分钟左右您将得到回复。