参数资料
型号: PS21965-4A
厂商: POWEREX INC
元件分类: 运动控制电子
英文描述: AC MOTOR CONTROLLER, 40 A, DMA24
封装: DIP-24
文件页数: 7/8页
文件大小: 956K
代理商: PS21965-4A
PS21965-4, PS21965-4A, PS21965-4C
Intellimod Module
Dual-In-Line Intelligent Power Module
20 Amperes/600 Volts
Powerex, Inc., 173 Pavilion Lane,Youngwood, Pennsylvania 15697-1800 (724) 925-7272
7
Rev. 12/09
Protection Function Timing Diagrams
C1
C4
C5
C2
UVDt
C6
C3
SET
RESET
HIGH LEVEL (NO FAULT OUTPUT)
UVDBr
CONTROL INPUT
PROTECTION
CIRCUIT STATE
CONTROL SUPPLY
VOLTAGE VDB
OUTPUT CURRENT IC
FAULT OUTPUT FO
Under-Voltage Protection (Upper-side, UVDB)
C1: Control supply voltage rises – After the voltage level reaches UVDBr, the drive circuit begins to work
at the rising edge of the next input signal.
C2: Normal operation – IGBT turn on and conducting current.
C3: Under-voltage trip (UVDBt).
C4: IGBT stays off regardless of the control input level, but there is no FO signal output.
C5: Under-voltage reset (UVDr).
C6: Normal operation – IGBT turn on and conducting current.
Typical Interface Circuit
Wiring Method Around Shunt Resistor
VNC
N
DIP-IPM
Wiring inductance should be less than 10nH.
(Equivalent to the inductance of a copper pattern with
length = 17mm, width = 3mm, and thickness = 100um.)
RSHUNT (Chip type resistor is recommended.)
This GND wiring from VNC should be as
close to the shunt resistors as possible.
UP, VP, WP, UN, VN, WN
MCU
5V LINE
10kΩ
3.3kΩ (MIN)
FO
VNC (LOGIC)
DIP-IPM
NOTE: RC coupling at each input
(parts shown dotted) may change
depending on the PWM control
scheme used in the application and
the wiring impedance of the printed
circuit board. The DIP-IPM input signal
section integrates a 3.3kΩ (min)
pull-down resistor. Therefore, when
using an external filtering resistor, care
must be taken to satisfy the turn-on
threshold voltage requirement.
相关PDF资料
PDF描述
PS21965-ST AC MOTOR CONTROLLER, 40 A, DMA25
PS21993-4AE AC MOTOR CONTROLLER, DMA25
PS21993-4CE AC MOTOR CONTROLLER, DMA25
PS21994-4 AC MOTOR CONTROLLER, DMA25
PS21994-4A AC MOTOR CONTROLLER, DMA25
相关代理商/技术参数
参数描述
PS21965-4C 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:600V/20A low-loss CSTBTTM inverter bridge for three phase DC-to-AC power conversion
PS21965-4S 功能描述:MOD IPM 600V 20A SUPRMINIDIP RoHS:是 类别:半导体模块 >> 功率驱动器 系列:Intellimod™ 标准包装:15 系列:SPM® 类型:FET 配置:三相反相器 电流:1.8A 电压:500V 电压 - 隔离:1500Vrms 封装/外壳:23-DIP 模块
PS21965-4S_08 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:Dual-In-Line Package Intelligent Power Module
PS21965-4W 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:600V/20A low-loss CSTBTTM inverter bridge for three phase DC-to-AC power conversion
PS21965-A 制造商:POWEREX 制造商全称:Powerex Power Semiconductors 功能描述:Dual-In-Line Intelligent Power Module 20 Amperes/600 Volts