- 您现在的位置：买卖IC网 > PDF目录65979 > PS22056 AC MOTOR CONTROLLER, 50 A, DMA28 PDF资料下载
参数资料
| 型号： | PS22056 |
| 元件分类： | 运动控制电子 |
| 英文描述： | AC MOTOR CONTROLLER, 50 A, DMA28 |
| 封装： | DIP-28 |
| 文件页数： | 8/9页 |
| 文件大小： | 117K |
| 代理商： | PS22056 |
MITSUBISHI SEMICONDUCTOR <Dual-In-Line Package Intelligent Power Module>
PS22056
TRANSFER-MOLD TYPE
INSULATED TYPE
May 2005
MCU
10k
UP,VP,WP,UN,VN,WN
VNC(Logic)
Fo
DIP-IPM
5V line
Error output Fo
Output current Ic
Control supply voltage VDB
Protection circuit state
Control input
c6
c1
c2
c4
c5
c3
RESET
UVDBt
UVDBr
SET
RESET
High-level (no fault output)
[C] Under-Voltage Protection (Upper-side, UVDB)
c1. Control supply voltage rises : After the voltage reaches UVDBr, the circuits start to operate when next input is applied.
c2. Normal operation : IGBT ON and carrying current.
c3. Under voltage trip (UVDBt).
c4. IGBT OFF in spite of control input signal level, but there is no FO signal output.
c5. Under voltage reset (UVDBr).
c6. Normal operation : IGBT ON and carrying current.
Fig. 6 MCU I/O INTERFACE CIRCUIT
Note : RC coupling at each input (parts shown dotted) may change depending on the PWM control scheme used in
the application and the wiring impedance of the application’s printed circuit board.
The DIP-IPM input signal section integrates a 2.5k
(min) pull-down resistor. Therefore, when using a external
filtering resistor, pay attention to the turn-on threshold voltage requirement.
Fig. 7 WIRING CONNECTION WITH 1 SHUNT RESISTOR
Using low inductance chip resistor and reducing
wiring length to minimize the wiring inductance.
VNC
NW
NV
NU
DIP-IPM
Shunt resistor
For 3 shunt resistors connection, please refer to Fig.9.
Please insert fast
recovery type diode
between VNC and
NU, NV, NW terminals.
Please make the wiring connection
of shunt resistor to GND as short as
possible.
相关PDF资料 |
PDF描述 |
|---|---|
| PS22A73 | AC MOTOR CONTROLLER, 20 A, XMA42 |
| PS22A76 | AC MOTOR CONTROLLER, 50 A, DMA42 |
| PS302ESA | 1-CHANNEL, SGL POLE SGL THROW SWITCH, PDSO8 |
| PS302CSAX | 1-CHANNEL, SGL POLE SGL THROW SWITCH, PDSO8 |
| PS303CSAX | 1-CHANNEL, SGL POLE DOUBLE THROW SWITCH, PDSO8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PS22056_12 | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:Dual-In-Line Package Intelligent Power Module |
| PS2206FNS | 制造商:C&K Components 功能描述:SWITCH PUSHBUTTON 制造商:C&K Components 功能描述:PS2206FNS / Alt#: HAPS0044 / Series: COMAX |
| PS-2206-L NS | 功能描述:按钮开关 DPDT Plunger 30VDC RoHS:否 制造商:C&K Components 触点形式:2 NC - 2 NO 开关功能:ON ? OFF 电流额定值:4 A 电压额定值 AC:12 V to 250 V 电压额定值 DC:12 V to 50 V 功率额定值: 安装风格:Through Hole 照明:Illuminated 照明颜色:None IP 等级:IP 40 端接类型:Solder 触点电镀:Silver 执行器:Square 盖颜色: 封装: 可燃性等级:UL 94 V-0 |
| PS2206LNS | 制造商:C&K Components 功能描述:PS2206LNS / Alt#: HAPS0045 / Series: COMAX |
| PS2-211B | 功能描述:SWITCH PUSH DPDT 0.4VA 28V RoHS:是 类别:开关 >> 按钮 系列:PS 标准包装:1 系列:A16 类型:标准，发光式 电路:双刀双掷 开关功能:开-瞬时 额定电流:5A（AC） 额定电压 - AC:125V 额定电压 - DC:- 触动器类型:方形，按钮 颜色 - 致动器/盖:黄 发光类型，颜色:LED，黄 发光电压:12 VDC 安装类型:前面板安装 端接类型:焊接，快速连接 - 0.110"（2.8mm） 防护等级:IP65 - 防尘/防油/防水 特点:- 面板切口尺寸:圆形 - 直径 16.00mm 包装:散装 工作温度:-10°C ~ 55°C 机械寿命:2,000,000 次循环 电气寿命:100,000 次循环 其它名称:A165LAYM12D2 |
发布紧急采购，3分钟左右您将得到回复。