- 您现在的位置：买卖IC网 > PDF目录224796 > PS9817-1-V-F4 (California Eastern Laboratories) Power Resistor; Series:MK; Resistance:10ohm; Resistance Tolerance:+/- 1 %; Power Rating:0.75W; Voltage Rating:400V; Temperature Coefficient:+/-50 ppm; Mounting Type:Through Hole; Operating Temp. Min:0 C; Terminal Type:Radial Leaded PDF资料下载
参数资料
| 型号： | PS9817-1-V-F4 |
| 厂商： | California Eastern Laboratories |
| 英文描述： | Power Resistor; Series:MK; Resistance:10ohm; Resistance Tolerance:+/- 1 %; Power Rating:0.75W; Voltage Rating:400V; Temperature Coefficient:+/-50 ppm; Mounting Type:Through Hole; Operating Temp. Min:0 C; Terminal Type:Radial Leaded |
| 中文描述： | 邻舍高CMR，10Mbps的集电极开路输出型8引脚SSOP（以SO - 8）高速光电耦合器 |
| 文件页数： | 3/12页 |
| 文件大小： | 592K |
| 代理商： | PS9817-1-V-F4 |
PS9817-1,-2
NOTES ON HANDLING
1. Recommended soldering conditions
(1) Infrared reow soldering
Peak reow temperature
260°C or below (package surface temperature)
Time of peak reow temperature
10 seconds or less
Time of temperature higher than 220°C
60 seconds or less
Time to preheat temperature from 120 to 180°C 120±30 s
Number of reows
Three
Flux
Rosin ux containing small amount of chlorine (The ux with a maximum
chlorine content of 0.2 Wt% is recommended.)
(2) Wave soldering
Temperature
260°C or below (molten solder temperature)
Time
10 seconds or less
Preheating conditions
120°C or below (package surface temperature)
Number of times
One (Allowed to be dipped in solder including plastic mold portion.)
Flux
Rosin ux containing small amount of chlorine (The ux with a maximum chlorine content of 0.2
Wt% is recommended.)
(3) Soldering by Soldering Iron
Peak Temperature (lead part temperature) 350°C or below
Time (each pins)
3 seconds or less
Flux
Rosin ux containing small amount of chlorine (The ux with a maximum
chlorine content of 0.2 Wt% is recommended.)
(a) Soldering of leads should be made at the point 1.5 to 2.0 mm from the root of the lead
(b) Please be sure that the temperature of the package would not be heated over 100°C
120±30 s
(preheating)
220C
180C
Package
Surface
T
emperature
T
(C)
Time (s)
Recommended Temperature Profile of Infrared Reflow
(heating)
to 10 s
to 60 s
260C MAX.
120C
相关PDF资料 |
PDF描述 |
|---|---|
| PSB3AC | VCO |
| PSCIA2CHP-1 | P-CHANNEL, Si, SMALL SIGNAL, JFET |
| PSD2-24 | POWER TRANSFORMER, 1.1 VA |
| PSD2-28 | POWER TRANSFORMER, 1.1 VA |
| PSD2-36 | POWER TRANSFORMER, 1.1 VA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PS9817-2 | 制造商:CEL 制造商全称:CEL 功能描述:NECs HIGH CMR, 10Mbps OPEN COLLECTOR OUTPUT TYPE 8-PIN SSOP (SO-8) HIGH-SPEED OPTOCOUPLER |
| PS9817-2-A | 功能描述:高速光耦合器 10Mbps H-Spd Digital RoHS:否 制造商:Avago Technologies 电流传递比: 最大波特率: 最大正向二极管电压:1.75 V 最大反向二极管电压:5 V 最大功率耗散:40 mW 最大工作温度:+125 C 最小工作温度:- 40 C 封装 / 箱体:SOIC-5 封装:Tube |
| PS9817-2-AX | 功能描述:高速光耦合器 SO8 DulCH HISpd Digi Cpler 10Mb HI Perf RoHS:否 制造商:Avago Technologies 电流传递比: 最大波特率: 最大正向二极管电压:1.75 V 最大反向二极管电压:5 V 最大功率耗散:40 mW 最大工作温度:+125 C 最小工作温度:- 40 C 封装 / 箱体:SOIC-5 封装:Tube |
| PS9817-2-F3 | 制造商:CEL 制造商全称:CEL 功能描述:NECs HIGH CMR, 10Mbps OPEN COLLECTOR OUTPUT TYPE 8-PIN SSOP (SO-8) HIGH-SPEED OPTOCOUPLER |
| PS9817-2-F3-A | 功能描述:PHOTOCOUPLER HS DGTL OC OUT SMD RoHS:是 类别:隔离器 >> 光隔离器 - 逻辑输出 系列:NEPOC 标准包装:1,000 系列:- 电压 - 隔离:7500Vrms 通道数:1，单向 电流 - 输出 / 通道:50mA 数据速率:5MHz 传输延迟高 - 低 @ 如果:100ns 电流 - DC 正向(If):5mA 输入类型:DC 输出类型:开路集电极 安装类型:表面贴装 封装/外壳:6-SMD 供应商设备封装:6-SMD 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。