- 您现在的位置：买卖IC网 > PDF目录376256 > PSD313-A-90J (意法半导体) Low Cost Field Programmable Microcontroller Peripherals PDF资料下载
参数资料
| 型号： | PSD313-A-90J |
| 厂商： | 意法半导体 |
| 英文描述： | Low Cost Field Programmable Microcontroller Peripherals |
| 中文描述： | 低成本现场可编程微控制器外围设备 |
| 文件页数： | 13/85页 |
| 文件大小： | 691K |
| 代理商： | PSD313-A-90J |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页
PSD3XX Famly
10
8.0
Operating
Modes (MCU
Configurations)
The PSD3XX’s four operating modes enable it to interface directly to most 8- and 16-bit
microcontrollers with multiplexed and non-multiplexed address/data busses. The 16-bit
modes are not available to some devices; see Table 1. The following are the four operating
modes available:
J
Multiplexed 8-bit address/data bus
J
Multiplexed 16-bit address/data bus
J
Non-multiplexed 8-bit data bus
J
Non-multiplexed 16-bit data bus
Please read the section below that corresponds to your type of MCU. Then check the
appropriate Figure (3A/3B/3C/3D) to determine your pin connections. Table 3 lists the Port
connections in tabular form.
Multiplexed 8-bit address/data bus (Figure 3A)
This mode is used to interface to microcontrollers with a multiplexed 8-bit data bus. Since
the low-order address and data are multiplexed together, your MCU will output an ALE
or AS signal. The PSD3XX contains a transparent latch to demultiplex the address/data
lines internally. All you have to do is connect the ALE/AS signal and select 8-bit multiplexed
bus mode in PSDsoft. If your MCU outputs more than 16 bits of address, and you
wish to connect them to the PSD, connect A16-A18 to Port C and A19 to A19/CSI, where
applicable.
Multiplexed 16-bit address/data bus (Figure 3B)
This mode is used to interface to microcontrollers with a multiplexed 16-bit data bus. Since
the low address bytes and data are multiplexed together, your MCU will output an ALE
or AS signal. The PSD3XX contains a transparent latch to demultiplex the address/data
lines internally. All you have to do is connect the ALE/AS signal and select 8-bit multiplexed
bus mode in PSDsoft. If your MCU outputs more than 16 bits of address, and you
wish to connect them to the PSD, connect A16-A18 to Port C and A19 to A19/CSI, where
applicable.
Non-multiplexed 8-bit data bus (Figure 3C)
This mode is used to interface to microcontrollers with a non-multiplexed 8-bit data bus.
Connect the MCU’s address bus to AD0/A0-AD15/A15 on the PSD. Connect the data bus
signals of your MCU to Port A of the PSD. If your MCU outputs more than 16 bits of
address, and you wish to connect them to the PSD, connect A16-A18 to Port C and A19 to
A19/CSI, where applicable.
Non-multiplexed 16-bit data bus (Figure 3D)
This mode is used to interface to microcontrollers with a non-multiplexed 16-bit data bus.
Connect the MCU’s address bus to AD0/A0-AD15/A15 on the PSD. Connect the low byte
data bus signals of your MCU to Port A, and the high byte data output of your MCU to Port
B of the PSD. If your MCU outputs more than 16 bits of address, and you wish to connect
them to the PSD, connect A16-A18 to Port C and A19 to A19/CSI, where applicable.
For users with multiplexed MCUs that have data multiplexed on address lines other
than A0-A7 note:
You can still use the PSD3XX, but you will have to connect your
data to Port A (and Port B where required), as shown in Figure 3C or 3D. That is, you will
be connecting it as if you were using a non-multiplexed MCU. In this case, you must
connect the ALE/AS signal so that the address will still be properly latched. This option is
not available on the 3X1 versions.
相关PDF资料 |
PDF描述 |
|---|---|
| PSD313-A-90JI | Current Mode PWM Controller 14-SOIC 0 to 70 |
| PSD313-A-90JM | Current Mode PWM Controller 8-SOIC 0 to 70 |
| PSD313-B-15J | Current Mode PWM Controller 8-SOIC 0 to 70 |
| PSD313-B-15L | Current Mode PWM Controller 8-SOIC 0 to 70 |
| PSD313-B-15M | Current Mode PWM Controller 8-SOIC 0 to 70 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PSD313-A-90JI | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Low Cost Field Programmable Microcontroller Peripherals |
| PSD313-A-90JM | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Low Cost Field Programmable Microcontroller Peripherals |
| PSD313-B-15J | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Low Cost Field Programmable Microcontroller Peripherals |
| PSD313B-15J | 功能描述:SPLD - 简单可编程逻辑器件 5V 1M (128Kx8) 150ns RoHS:否 制造商:Texas Instruments 逻辑系列:TICPAL22V10Z 大电池数量:10 最大工作频率:66 MHz 延迟时间:25 ns 工作电源电压:4.75 V to 5.25 V 电源电流:100 uA 最大工作温度:+ 75 C 最小工作温度:0 C 安装风格:Through Hole 封装 / 箱体:DIP-24 |
| PSD313-B-15L | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Low Cost Field Programmable Microcontroller Peripherals |
发布紧急采购，3分钟左右您将得到回复。