参数资料
型号: PSD501B1-C-15L
厂商: 意法半导体
英文描述: Low Cost Field Programmable Microcontroller Peripherals
中文描述: 低成本现场可编程微控制器外围设备
文件页数: 9/153页
文件大小: 1036K
代理商: PSD501B1-C-15L
PSD5XX Famly
6
Upon each address or logic input change to the PSD, the device powers up from low power
standby for a short time. Then the PSD consumes only the necessary power to deliver new
logic or memory data to its outputs as a response to the input change. After the new
outputs are stable, the PSD latches them and automatically reverts back to standby mode.
The I
CC
current flowing during standby mode and during DC operation is identical.
The PSD automatically reduces its DC current drain to these low levels and does not
require controlling by the CSI (Chip Select) input. Disabling the CSI pin unconditionally
forces the PSD to standby mode independent of other input transitions.
The only significant power consumption in the PSD occurs during AC operation.
The PSD contains the first architecture to apply Zero-power techniques to memory circuit
blocks as well as logic.
Figure 2 compares PSD Zero-power operation to the operation of a discrete solution.
A standard microcontroller (MCU) bus cycle usually starts with an ALE (or AS) pulse and
the generation of an address. The PSD detects the address transition and powers up for a
short time. The PSD then latches the outputs of the PAD, EPROM and SRAM to the new
values. After finishing these operations, the PSD shuts off its internal power, entering
standby mode. The time taken for the entire cycle is less than the PSD’s “access time.”
The PSD will stay in standby mode if the inputs do not change between bus cycles. In an
alternate system implementation using discrete EPROM, SRAM and other discrete
components, the system will consume operating power during the entire bus cycle. This is
because the chip select inputs on the memory devices are usually active throughout the
entire cycle. The AC power consumption of the PSD may be calculated using the composite
frequency of the MCU address and control inputs, as well as any other logic inputs to the
ZPLD.
NOTE:
The ZPSD5XX parts have been rated for a lower standby current (I
SB
) than the
PSD5XX parts.
5.0
Integrated
Power
Management
Operation
TM
ALE
DISCRETE EPROM, SRAM & LOGIC
ADDRESS
EPROM
ACCESS
SRAM
ACCESS
EPROM
ACCESS
I
CC
ZPSD
ZPSD
ZPSD
TIME
Figure 2. ZPSDPower Operation vs. Dscrete Implementation
相关PDF资料
PDF描述
PSD511B1-C-15L Low Cost Field Programmable Microcontroller Peripherals
PSD501B1-C-15U Low Cost Field Programmable Microcontroller Peripherals
PSD511B1-C-15U Low Cost Field Programmable Microcontroller Peripherals
PSD501B1-C-70J Low Cost Field Programmable Microcontroller Peripherals
PSD511B1-C-70J Low Cost Field Programmable Microcontroller Peripherals
相关代理商/技术参数
参数描述
PSD501B1-C-15U 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Low Cost Field Programmable Microcontroller Peripherals
PSD501B1-C-70J 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Low Cost Field Programmable Microcontroller Peripherals
PSD501B1-C-70L 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Low Cost Field Programmable Microcontroller Peripherals
PSD501B1-C-70U 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Low Cost Field Programmable Microcontroller Peripherals
PSD501B1-C-90JI 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Low Cost Field Programmable Microcontroller Peripherals