收藏本站
参数资料
型号： PSD814F2-20
厂商： 意法半导体
英文描述： Flash In-System Programmable (ISP) Peripherals for 8-bit MCUs, 5V
中文描述： Flash在系统可编程（ISP）的周边8位MCU，5V的
文件页数： 67/110页
文件大小： 1737K
代理商： PSD814F2-20
67/110
PSD813F2, PSD833F2, PSD834F2, PSD853F2, PSD854F2
RESET TIMING AND DEVICE STATUS AT RESET
Power-Up Reset
Upon Power-up, the PSD requires a Reset (RE-
SET) pulse of duration t
NLNH-PO
after V
CC
is
steady. During this period, the device loads inter-
nal configurations, clears some of the registers
and sets the Flash memory into Operating mode.
After the rising edge of Reset (RESET), the PSD
remains in the Reset mode for an additional peri-
od, t
OPR
, before the first memory access is al-
lowed.
The Flash memory is reset to the READ Mode
upon Power-up. Sector Select (FS0-FS7 and
CSBOOT0-CSBOOT3) must all be Low, Write
Strobe (WR, CNTL0) High, during Power On Re-
set for maximum security of the data contents and
to remove the possibility of a byte being written on
the first edge of Write Strobe (WR, CNTL0). Any
Flash memory WRITE cycle initiation is prevented
automatically when V
CC
is below V
LKO
.
Warm Reset
Once the device is up and running, the device can
be reset with a pulse of a much shorter duration,
t
NLNH
.
The same t
OPR
period is needed before the device
is operational after warm reset. Figure
34
shows
the timing of the Power-up and warm reset.
I/O Pin, Register and PLD Status at Reset
Table 33., page 68
shows the I/O pin, register and
PLD status during Power On Reset, warm reset
and Power-down mode. PLD outputs are always
valid during warm reset, and they are valid in Pow-
er On Reset once the internal PSD Configuration
bits are loaded. This loading of PSD is completed
typically long before the V
CC
ramps up to operat-
ing level. Once the PLD is active, the state of the
outputs are determined by the PSDabel equa-
tions.
Reset of Flash Memory Erase and Program
Cycles (on the PSD834Fx)
A Reset (RESET) also resets the internal Flash
memory state machine. During a Flash memory
Program or Erase cycle, Reset (RESET) termi-
nates the cycle and returns the Flash memory to
the Read Mode within a period of t
NLNH-A
.
Figure 34. Reset (RESET) Timing
tNLNH-PO
Power-On Reset
tOPR
AI02866b
RESET
tNLNH
tNLNH-A
Warm Reset
tOPR
V
CC
V
CC
(min)
相关PDF资料
PDF描述
PSD814F2-70 Flash In-System Programmable (ISP) Peripherals for 8-bit MCUs, 5V
PSD814F2-90 Flash In-System Programmable (ISP) Peripherals for 8-bit MCUs, 5V
PSD833F2V-12 Flash In-System Programmable (ISP) Peripherals for 8-bit MCUs, 5V
PSD833F2V-15 Flash In-System Programmable (ISP) Peripherals for 8-bit MCUs, 5V
PSD833F2V-20 Flash In-System Programmable (ISP) Peripherals for 8-bit MCUs, 5V
相关代理商/技术参数
参数描述
PSD833F2-90J 功能描述:CPLD - 复杂可编程逻辑器件 5.0V 1M 90ns RoHS:否 制造商:Lattice 系列: 存储类型:EEPROM 大电池数量:128 最大工作频率:333 MHz 延迟时间:2.7 ns 可编程输入/输出端数量:64 工作电源电压:3.3 V 最大工作温度:+ 90 C 最小工作温度:0 C 封装 / 箱体:TQFP-100
PSD833F2-90JI 功能描述:SPLD - 简单可编程逻辑器件 5.0V 1M 90ns RoHS:否 制造商:Texas Instruments 逻辑系列:TICPAL22V10Z 大电池数量:10 最大工作频率:66 MHz 延迟时间:25 ns 工作电源电压:4.75 V to 5.25 V 电源电流:100 uA 最大工作温度:+ 75 C 最小工作温度:0 C 安装风格:Through Hole 封装 / 箱体:DIP-24
PSD833F2-90M 功能描述:SPLD - 简单可编程逻辑器件 5.0V 1M 90ns RoHS:否 制造商:Texas Instruments 逻辑系列:TICPAL22V10Z 大电池数量:10 最大工作频率:66 MHz 延迟时间:25 ns 工作电源电压:4.75 V to 5.25 V 电源电流:100 uA 最大工作温度:+ 75 C 最小工作温度:0 C 安装风格:Through Hole 封装 / 箱体:DIP-24
PSD833F2-90MI 功能描述:CPLD - 复杂可编程逻辑器件 5.0V 1M 90ns RoHS:否 制造商:Lattice 系列: 存储类型:EEPROM 大电池数量:128 最大工作频率:333 MHz 延迟时间:2.7 ns 可编程输入/输出端数量:64 工作电源电压:3.3 V 最大工作温度:+ 90 C 最小工作温度:0 C 封装 / 箱体:TQFP-100
PSD834F2-15M 制造商:STMicroelectronics 功能描述:Flash In-System Programmable Peripherals 52-Pin PQFP
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*