收藏本站
参数资料
型号： PSD9534V15MIT
厂商： 意法半导体
英文描述： IC DVI/HDMI MUX/DEMUX 48TSSOP
中文描述： Flash在系统可编程ISP的外设的8位微控制器
文件页数： 40/110页
文件大小： 1737K
代理商： PSD9534V15MIT
PSD813F2, PSD833F2, PSD834F2, PSD853F2, PSD854F2
40/110
Input Macrocells (IMC)
The CPLD has 24 Input Macrocells (IMC), one for
each pin on Ports A, B, and C. The architecture of
the Input Macrocells (IMC) is shown in
Figure
17., page 41
. The Input Macrocells (IMC) are indi-
vidually configurable, and can be used as a latch,
register, or to pass incoming Port signals prior to
driving them onto the PLD input bus. The outputs
of the Input Macrocells (IMC) can be read by the
MCU through the internal data bus.
The enable for the latch and clock for the register
are driven by a multiplexer whose inputs are a
product term from the CPLD AND Array or the
MCU Address Strobe (ALE/AS). Each product
term output is used to latch or clock four Input
Macrocells (IMC). Port inputs 3-0 can be con-
trolled by one product term and 7-4 by another.
Configurations for the Input Macrocells (IMC) are
specified by equations written in PSDabel (see Ap-
plication Note
AN1171
). Outputs of the Input Mac-
rocells (IMC) can be read by the MCU via the IMC
buffer.
See
the
section
PORTS, page 51
.
entitled
I/O
Input Macrocells (IMC) can use Address Strobe
(ALE/AS, PD0) to latch address bits higher than
A15. Any latched addresses are routed to the
PLDs as inputs.
Input Macrocells (IMC) are particularly useful with
handshaking communication applications where
two processors pass data back and forth through
a common mailbox.
Figure 18., page 42
shows a
typical configuration where the Master MCU writes
to the Port A Data Out Register. This, in turn, can
be read by the Slave MCU via the activation of the
“Slave-Read” output enable product term.
The Slave can also write to the Port A Input Mac-
rocells (IMC) and the Master can then read the In-
put Macrocells (IMC) directly.
Note that the “Slave-Read” and “Slave-Wr” signals
are product terms that are derived from the Slave
MCU inputs Read Strobe (RD, CNTL1), Write
Strobe (WR, CNTL0), and Slave_CS.
相关PDF资料
PDF描述
PSD9132V20MIT Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD8332V20MIT Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD9332V20MIT Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD9332V20JIT Proximity Sensor; Sensor Input Type:Inductive; Sensing Range Max:8mm; Sensor Output Type:NO; Load Current Max:100mA; Output Type:Transistor; Sensing Face Diameter:30mm; Sensor Housing:Barrel; Supply Voltage Max:60VDC
PSD8532V20JIT Proximity Sensor; Sensor Input Type:Inductive; Sensing Range Max:8mm; Sensor Output Type:NO; Load Current Max:300mA; Load Current Min:8mA; Output Type:NO; Sensing Face Diameter:30mm; Sensor Housing:Barrel; Supply Voltage Max:250V
相关代理商/技术参数
参数描述
PSD954F2-90J 功能描述:SPLD - 简单可编程逻辑器件 U 511-PSD854F2-90J RoHS:否 制造商:Texas Instruments 逻辑系列:TICPAL22V10Z 大电池数量:10 最大工作频率:66 MHz 延迟时间:25 ns 工作电源电压:4.75 V to 5.25 V 电源电流:100 uA 最大工作温度:+ 75 C 最小工作温度:0 C 安装风格:Through Hole 封装 / 箱体:DIP-24
PSD954F2-90M 功能描述:SPLD - 简单可编程逻辑器件 U 511-PSD854F2-90M RoHS:否 制造商:Texas Instruments 逻辑系列:TICPAL22V10Z 大电池数量:10 最大工作频率:66 MHz 延迟时间:25 ns 工作电源电压:4.75 V to 5.25 V 电源电流:100 uA 最大工作温度:+ 75 C 最小工作温度:0 C 安装风格:Through Hole 封装 / 箱体:DIP-24
PSD954F2V-90J 功能描述:SPLD - 简单可编程逻辑器件 5.0V 2M 90ns RoHS:否 制造商:Texas Instruments 逻辑系列:TICPAL22V10Z 大电池数量:10 最大工作频率:66 MHz 延迟时间:25 ns 工作电源电压:4.75 V to 5.25 V 电源电流:100 uA 最大工作温度:+ 75 C 最小工作温度:0 C 安装风格:Through Hole 封装 / 箱体:DIP-24
PSD954F2V-90M 功能描述:SPLD - 简单可编程逻辑器件 PQFP-52 3V 2M 90NS RoHS:否 制造商:Texas Instruments 逻辑系列:TICPAL22V10Z 大电池数量:10 最大工作频率:66 MHz 延迟时间:25 ns 工作电源电压:4.75 V to 5.25 V 电源电流:100 uA 最大工作温度:+ 75 C 最小工作温度:0 C 安装风格:Through Hole 封装 / 箱体:DIP-24
PS-DA0104-01 制造商:POWER-SYSTEMS 制造商全称:Power Systems GmbH+Co.KG 功能描述:DC-AC INVERTER UNIT 4 W SINGLE OUTPUTS
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*