- 您现在的位置：买卖IC网 > Datasheet目录500 > PT334-6B (Everlight Electronics Co Ltd)PHOTOTRANSISTOR 5MM BLACK RAD Datasheet资料下载
参数资料
| 型号： | PT334-6B |
| 厂商： | Everlight Electronics Co Ltd |
| 文件页数： | 8/9页 |
| 文件大小： | 0K |
| 描述： | PHOTOTRANSISTOR 5MM BLACK RAD |
| 标准包装： | 500 |
| 电压 - 集电极发射极击穿（最大）： | 30V |
| 电流 - 集电极 (Ic)（最大）： | 20mA |
| 电流 - 暗 (Id)（最大）： | 100nA |
| 波长： | 940nm |
| 安装类型： | 通孔 |
| 方向： | 顶视图 |
| 封装/外壳： | 径向，T-1 透镜 |
| 其它名称： | 1080-1158 |
DATASHEET
5mm Phototransistor
PT334-6B
Notes
1.
Lead Forming
?
?
?
?
?
During lead formation, the leads should be bent at a point at least 3mm from the base of the epoxy bulb.
Lead forming should be done before soldering.
Avoid stressing the LED package during leads forming. The stress to the base may damage the LED’s characteristics or it
may break the LEDs.
Cut the LED lead frames at room temperature. Cutting the lead frames at high temperatures may cause failure of the LEDs.
When mounting the LEDs onto a PCB, the PCB holes must be aligned exactly with the lead position of the LED. If the LEDs
are mounted with stress at the leads, it causes deterioration of the epoxy resin and this will degrade the LEDs.
2.
Storage
?
?
The LEDs should be stored at 30°C or less and 70%RH or less after being shipped from Everlight and the storage life limits
are 3 months. If the LEDs are stored for 3 months or more, they can be stored for a year in a sealed container with a
nitrogen atmosphere and moisture absorbent material.
Please avoid rapid transitions in ambient temperature, especially, in high humidity environments where condensation can
occur.
3.
Soldering
?
?
Careful attention should be paid during soldering. When soldering, leave more then 3mm from solder joint to epoxy bulb,
and soldering beyond the base of the tie bar is recommended.
Recommended soldering conditions:
Hand Soldering
DIP Soldering
Temp. at tip of iron
Soldering time
Distance
300 ℃ Max. (30W Max.)
3 sec Max.
3mm Min.(From solder
joint to epoxy bulb)
Preheat temp.
Bath temp. & time
Distance
100 ℃ Max. (60 sec Max.)
260 Max., 5 sec Max
3mm Min. (From solder
joint to epoxy bulb)
?
?
?
?
Recommended soldering profile
laminar wave
Fluxing
Prehead
Avoiding applying any stress to the lead frame while the LEDs are at high temperature particularly when soldering.
Dip and hand soldering should not be done more than one time
After soldering the LEDs, the epoxy bulb should be protected from mechanical shock or vibration until the LEDs return to
room temperature.
8
www.everlight.com
:3
Revision Copyright ?
LifecyclePhase:
No: Release
2010, Everlight All Rights Reserved. Release Date : May.28.2013. Issue DPT-0000263 Date:2013-06-04 09:56:18.0
Expired Period: Forever
相关PDF资料 |
PDF描述 |
|---|---|
| PT334-6C | PHOTOTRANSISTOR 5MM CLEAR RAD |
| PT42-21B/TR8 | PHOTOTRANSISTOR 1.8MM RND BK SMD |
| PT4800E0000F | PHOTO TRANS CLEAR LEN 800NM SIDE |
| PT4800FE000F | PHOTO TRANS BLACK LEN 860NM SIDE |
| PT480E00000F | PHOTO TRANS CLEAR LEN 800NM SIDE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PT334-6B_05 | 制造商:EVERLIGHT 制造商全称:Everlight Electronics Co., Ltd 功能描述:5mm Phototransistor T-1 |
| PT334-6C | 功能描述:光电晶体管 Phototransistor RoHS:否 制造商:OSRAM Opto Semiconductors 最大功率耗散:165 mW 最大暗电流:200 nA 封装 / 箱体:T-1 |
| PT334-6C_05 | 制造商:EVERLIGHT 制造商全称:Everlight Electronics Co., Ltd 功能描述:5mm Phototransistor T-1 3/4 |
| PT334-6C_09 | 制造商:EVERLIGHT 制造商全称:Everlight Electronics Co., Ltd 功能描述:5mm Phototransistor T-1 3/4 |
| PT33A0803ST69 | 制造商:ITT Interconnect Solutions 功能描述:CONN RCPT 3POS WALL MNT SKT |
发布紧急采购，3分钟左右您将得到回复。