- 您现在的位置：买卖IC网 > PDF目录96791 > PT4485N (TEXAS INSTRUMENTS INC) 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | PT4485N |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 电源模块 |
| 英文描述： | 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
| 封装： | SIP-26 |
| 文件页数： | 6/9页 |
| 文件大小： | 215K |
| 代理商： | PT4485N |
Application Notes
For technical support and further information, visit http://power.ti.com
Using the Inhibit Function on the PT4470 &
PT4480 Series of Isolated DC/DC Converters
The PT4470/44480 series of DC/DC converters incor-
porate an On/Off Inhibit function. This function may be
used in applications that demand battery conservation,
power-up/shutdown sequencing, and/or to coordinate
power-up for active in-rush current control.
The On/Off feature is provided by the Inhibit control,
pin 3. The Inhibit pin of the PT4470/4480 series of
converters is an active low enable. The pin must be
either connected, or actively pulled low, to –Vin (pin 2)
to enable the converter output (see standard applica-
tion schematic). When pins 2 & 3 are connected, the
converter provides a regulated output whenever a valid
source voltage3 is applied between +Vin (pin 1), and –Vin
(pin 2). If pin 3 is disconnected, or allowed to become
high impedance, the regulator output will be disabled. 5
Table 2-1 provides details of the interface requirements
for the Inhibit pin. Figure 2-1 shows how a discrete
MOSFET (Q1) 4, may be referenced to –Vin and used to
control the input.
Table 2-1 Inhibit Control Requirements
Parameter
Min
Max
Enable (VIH)
–0.5 V
0.8 V
Disable (VIL)
2.5 V
(Open Circuit)
Notes:
1. The Inhibit control uses –Vin (pin 2), on the primary side
of the converter, as its ground reference. All voltages
specified are with respect to –Vin.
2. The internal circuitry is simple pull-up resistor. The
open-circuit voltage may be as high as 6.5 Vdc.
3. These converters incorporate an “Under-Voltage
Lockout” (UVLO) function. This function automatically
disables the converter output until there is sufficient input
voltage to produce a regulated output. Table 2 gives the
applicable UVLO thresholds.
Table 2-2 UVLO Thresholds 1
Series
UVLO Threshold
Vin Range
PT4470
17 V Typical
18 – 36 V
PT4480
34.5 V Typical
36 – 75 V
4. The Inhibit input must be controlled with an open-
collector (or open-drain) discrete transistor or
MOSFET.
Do not use a pull-up resistor.
5. When the converter output is disabled, the current
drawn from the input supply is typically reduced to
4 mA (10 mA maximum).
Figure 2-1
Turn-On Time:
With input power applied, the converter
typically produces a fully regulated output voltage within
25 ms after applying a low-voltage signal to the Inhibit
control pin. The actual turn-on time will vary with
the input voltage, output load, and the total amount of
capacitance connected to the output. Using the circuit of
Figure 2-1, Figure 2-2 shows the typical output voltage
and input current waveforms of a PT4472 after Q1 is
turned on. The turn on of Q1 correlates to the fall in
Vinh. The output voltage was set to 2.5 V. The waveform
was measured with a 48-Vdc input voltage, and 15-A load
current.
Figure 2-2
PT4470, PT4480 Series
6. Keep the on/off transition to less than 1ms. This
prevents erratic operation of the ISR, whereby the
output voltage may drift un-regulated between 0 V
and the rated output during power-up.
Vout (1V/Div)
Iin (2A/Div)
Vinh (5V/Div)
HORIZ SCALE: 5ms/Div
PT4472
+V
sns
+V
out
-V
out
-V
sns
7
8-13
14-19
20
21
25
22
24
23
VID0 - VID4
+V
in
–V
in
1
2
3
Inhibit
C
1
+
PROGRAMMING PINS
+2.5V
+V
IN
–V
IN
0V
1 =Enable
Q
1
BSS138
相关PDF资料 |
PDF描述 |
|---|---|
| PT4486C | 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
| PT4493A | 1-OUTPUT 100 W DC-DC BOOSTER MODULE |
| PT4493N | 1-OUTPUT 100 W DC-DC BOOSTER MODULE |
| PT4476N | 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
| PT4495C | 1-OUTPUT 100 W DC-DC BOOSTER MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PT4486 | 制造商:TI 制造商全称:Texas Instruments 功能描述:100-W 30-A Programmable Isolated DC/DC Converter |
| PT4486A | 功能描述:CONV DC-DC 12VADJ 48VIN 8.5A HRZ RoHS:是 类别:电源 - 板载 >> DC DC Converters 系列:PT4480 标准包装:10 系列:PT4570 类型:隔离 输出数:1 电压 - 输入（最小）:36V 电压 - 输入（最大）:75V Voltage - Output 1:9V Voltage - Output 2:- Voltage - Output 3:- 电流 - 输出（最大）:3.3A 电源（瓦） - 制造商系列:30W 电压 - 隔离:1.5kV（1500V） 特点:- 安装类型:表面贴装 封装/外壳:19-SIP SMD 模块 尺寸/尺寸:3.00" L x 1.19" W x 0.50" H（76.2mm x 30.2mm x 12.7mm） 包装:托盘 工作温度:-40°C ~ 85°C 效率:84% 电源（瓦特）- 最大:30W |
| PT4486C | 功能描述:开关变换器、稳压器与控制器 100W 48V-Input 12V Out Iso DC/DC Conv RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| PT4486N | 功能描述:CONV DC-DC 12VADJ 48VIN 8.5A VRT RoHS:是 类别:电源 - 板载 >> DC DC Converters 系列:PT4480 标准包装:10 系列:PT4570 类型:隔离 输出数:1 电压 - 输入（最小）:36V 电压 - 输入（最大）:75V Voltage - Output 1:9V Voltage - Output 2:- Voltage - Output 3:- 电流 - 输出（最大）:3.3A 电源（瓦） - 制造商系列:30W 电压 - 隔离:1.5kV（1500V） 特点:- 安装类型:表面贴装 封装/外壳:19-SIP SMD 模块 尺寸/尺寸:3.00" L x 1.19" W x 0.50" H（76.2mm x 30.2mm x 12.7mm） 包装:托盘 工作温度:-40°C ~ 85°C 效率:84% 电源（瓦特）- 最大:30W |
| PT4493 | 制造商:TI 制造商全称:Texas Instruments 功能描述:100-W 8.5-A Programmable Isolated DC/DC Converter |
发布紧急采购，3分钟左右您将得到回复。