参数资料
型号: PT5405N
厂商: Texas Instruments
文件页数: 8/15页
文件大小: 0K
描述: REG 1.5V 6A 5/3.3VIN VERT
标准包装: 30
系列: PT5400
类型: 非隔离(POL)
输出数: 1
电压 - 输入(最小): 3.1V
电压 - 输入(最大): 5.5V
Voltage - Output 1: 1.5V
电流 - 输出(最大): 5.5A
电源(瓦) - 制造商系列: 8W
安装类型: 通孔
封装/外壳: 5-SIP 模块
尺寸/尺寸: 0.90" L x 0.48" W x 0.95" H(22.9mm x 12.2mm x 24.1mm)
包装: 托盘
工作温度: -40°C ~ 85°C
效率: 85%
电源(瓦特)- 最大: 8.3W
其它名称: 296-32689
PT5405N-ND
Application Notes
PT5400 Series
Using the Inhibit Control of the PT5400 SWIFT ?
Series of Power Modules
For applications requiring output voltage On/Off control,
the PT5400 series of SWIFT power modules incorporate
an inhibit function. This function can be used wherever
there is a requirement for the module to be switched
off. The On/Off function is provided by the Inhibit
(pin 1) control.
The ISR functions normally with Pin 1 open-circuit,
providing a regulated output whenever a valid source
voltage is applied to V in , (pin 2). When a low-level 2
ground signal is applied to pin 1, the regulator output
will be disabled.
Figure 3-1 shows an application schematic, which details
the typical use of the Inhibit function. Note the discrete
transistor (Q1). The Inhibit control has its own internal
pull-up to +V in potential. An open-collector or open-drain
device is required to control this input 1 . The Inhibit pin
control thresholds are given in Table 3-1.
Table 3-1; Inhibit Control Requirements
Turn-On Time: In the circuit of Figure 3-1, turning Q 1
on applies a low-voltage to the Inhibit control (pin 1)
and disables the regulator output. Correspondingly,
turning Q 1 off allows the ISR to execute a soft-start
power up. The soft-start power up consists of a short
delay, t d , followed by a period, t (SS) , in which the output
voltage rises from zero to its full regulation voltage.
(See the section on Soft-Start Power Up). The module
produces a fully regulated output voltage within 25msec.
Figure 3-2 shows the typical rise in both output voltage
and input current for a PT5404 (1.8V), following the
turn-off of Q 1 . The turn off of Q 1 corresponds to the
drop in the Q 1 Vgs waveform. The time periods, t d and
t (SS) , are indicated. The waveforms were measured with
a 5Vdc input voltage, and 0.7- ? resistive load.
Figure 3-2
Parameter
Enable (VIH)
Min
Vin – 0.5
Max
Open
HORIZ SCALE: 5ms/Div
Disable (VIL)
–0.2V
+0.5V
Vout (1V/Div)
Iin (0.5A/Div)
Figure 3-1
+V IN
2
Vin
PT5401
Vo
4
+V O
Q1 Vgs (10V/Div)
INH
GND
Inhibit
C 1
1 0 0 μ F
Q1
BSS138
1
3
t d
t (SS)
COM
COM
Notes:
1. Use an open-collector device (preferably a discrete
transistor) for the Inhibit input. A pull-up resistor is not
necessary. To disable the output voltage, the control pin
should be pulled low to less than +0.5VDC.
For technical support and further information, visit http://power.ti.com
相关PDF资料
PDF描述
TACL226K004RTA CAP TANT 22UF 4V 10% 0603
RO-1212S/P CONV DC/DC 1W 12VIN 12VOUT
745211-8 CONN D-SUB PLUG 25POS 26-22AWG
VJ1206A182JBAAT4X CAP CER 1800PF 50V 5% NP0 1206
6-747843-7 CONN D-SUB PLUG R/A 37POS AU PCB
相关代理商/技术参数
参数描述
PT5406 制造商:TI 制造商全称:Texas Instruments 功能描述:6-A 5-V/3.3-V Input Adjustable SWIFT Power Module
PT5406A 功能描述:DC/DC转换器 1.2V 6A 3.3/5V Input Adj SWIFT Module RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压(标称): 输出端数量:1 输出电压(通道 1):3.3 V 输出电流(通道 1):600 mA 输出电压(通道 2): 输出电流(通道 2): 安装风格:SMD/SMT 封装 / 箱体尺寸:
PT5406C 功能描述:DC/DC转换器 1.2V 6A 3.3/5V Input Adj SWIFT Module RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压(标称): 输出端数量:1 输出电压(通道 1):3.3 V 输出电流(通道 1):600 mA 输出电压(通道 2): 输出电流(通道 2): 安装风格:SMD/SMT 封装 / 箱体尺寸:
PT5406N 功能描述:DC/DC转换器 1.2V 6A 3.3/5V Input Adj SWIFT Module RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压(标称): 输出端数量:1 输出电压(通道 1):3.3 V 输出电流(通道 1):600 mA 输出电压(通道 2): 输出电流(通道 2): 安装风格:SMD/SMT 封装 / 箱体尺寸:
PT5407 制造商:TI 制造商全称:Texas Instruments 功能描述:6-A 5-V/3.3-V Input Adjustable SWIFT Power Module