- 您现在的位置：买卖IC网 > Datasheet目录874 > PT5407N (Texas Instruments)REG SW 5/3.3VIN 1.0V 6A HORZ Datasheet资料下载
参数资料
| 型号： | PT5407N |
| 厂商： | Texas Instruments |
| 文件页数： | 6/15页 |
| 文件大小： | 0K |
| 描述： | REG SW 5/3.3VIN 1.0V 6A HORZ |
| 标准包装： | 30 |
| 系列： | PT5400 |
| 类型： | 非隔离（POL） |
| 输出数： | 1 |
| 电压 - 输入（最小）： | 3.1V |
| 电压 - 输入（最大）： | 5.5V |
| Voltage - Output 1： | 1V |
| 电流 - 输出（最大）： | 5.5A |
| 电源（瓦） - 制造商系列： | 5W |
| 安装类型： | 通孔，直角 |
| 封装/外壳： | 5-SIP 模块 |
| 尺寸/尺寸： | 0.90" L x 0.48" W x 0.95" H（22.9mm x 12.2mm x 24.1mm） |
| 包装： | 托盘 |
| 工作温度： | -40°C ~ 85°C |
| 效率： | 80% |
| 电源（瓦特）- 最大： | 5.5W |
Application Notes
PT5400 Series
Operating Features of the PT5400 SWIFT?
Series of Power Modules
Under-Voltage Lockout (UVLO)
The PT5400 SWIFT series of power modules incor-
porate an under-voltage lockout (UVLO) function. The
UVLO function provides a clean transition during power-
up and power-down, allowing the regulator to tolerate a
slowly rising input voltage. The UVLO prevents opera-
If desired, both time periods can be lengthened with the
addition of a low value capacitor between the Inhibit
control (pin 1) and the COM (pin 3). For a given value
of external capacitance, C inh , the formulas for calculating
the approximate effect on t d and t (SS) are given below.
tion of the module until the input voltage has risen above
2.95 V. Below this threshold the status of the inhibit
control pin is overriden, and the module will not produce
an output. When the input voltage rises above this thresh-
old, the output status of the module is determined by the
inhibit control pin. If the inhibit control is open-circuit
t d
t (SS)
≈ (C inh + 0.047 μF) × 1.2 V
5 μA
≈ (C inh + 0.047 μF) × 0.7 V
5 μA
(not grounded), the module will automatically power up.
The UVLO circuit has approximately 0.16 V of hysteresis,
and will completely turn off the module when a falling
input voltage drops below about 2.8 V. (Note: Even though
the applied input voltage may be above the UVLO threshold,
operation to the published specifications requires that the input
voltage be at or above the minimum specified for each model in
the series. This ensures that the output voltage of the module is in
regulation.)
Soft-Start Power Up
Following either the application of a valid input source
voltage, or the removal of a ground signal to the inhibit
control pin (with input power applied), the module will
initiate a soft-start power up. The soft start has two
effects on the start-up characteristic. It introduces a short
time delay prior to the start-up of the output voltage,
and also slows the rate at which the output voltage rises.
Figure 1-1 shows the power-up characteristic of a PT5404
(1.8 V). In this example the delay time, t d , is measured
from the point at which the input voltage rises above
2.95 V (the UVLO threshold), to the point that the output
voltage starts to rise. The time period t (SS) is the rise time
of the output voltage ramp. The value of t d and t (SS)
are are approximately 10 ms and 7.5 ms respectively.
Figure 1-1; Soft-Start Characteristic and Timing
HORIZ SCALE: 5ms/Div
Vin (1V/Div)
Vin =2.95V
Vout (1V/Div)
Note: The capacitor should be placed as close to the regulator as
possible. Adding 0.047 μF of external capacitance to the Inhibit
pin approximately doubles the value of t d and t (SS) .
Current Limit Protection
The output current limit feature is one of two fault
protection mechanisms built into the PT5400 modules.
Its purpose is to protect both the module and input source
against the occurance of a load fault, thereby isolating the
fault and preventing it from propagating to other parts
of the power system. The PT5400 regulators sense the
current switched by the series (high-side) power MOSFET.
The circuit implements a continuous current limit char-
acteristic. Upon the removal of the fault the output voltage
will promptly recover, and the module will return to nor-
mal operation.
A current limit condition will also increase the module’s
power dissipation, which may cause the temperature of
the internal components to significantly rise. If the con-
dition persists, the module may begin to cycle in and out
of thermal shutdown.
Thermal Shutdown
Thermal shutdown is the second fault protection mecha-
nism and protects the module’s internal circuitry against
excessively high temperatures. A rise in the temperature
of the internal circuitry may be the result of a drop in
airflow, a high ambient temperature, or a sustained over-
current load fault. If the junction temperature of the
internal components exceed 150 °C, the module will
shutdown. Once in thermal shutdown, the regulator is
disabled and the output voltage is reduced to zero. The
recovery is automatic and begins with a soft-start power
up. Recovery occurs when the the sensed temperature
decreases 10 °C below the trip point.
t d
t (SS)
For technical support and further information, visit http://power.ti.com
相关PDF资料 |
PDF描述 |
|---|---|
| PTB48560BAH | CONV DC/DC 3.3V 8A HZ T/H 11DIP |
| PTH03000WAD | MODULE PIP 3.3VIN 6A ADJ T/H |
| PTKM10-180SM | TOROIDAL POWER CHOKE 10UH SMD |
| PV37W504C01B00 | TRIMMER 500K OHM 0.25W TH |
| PVC6282 | CAP FILM 8200PF 600VDC RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PT5408 | 制造商:TI 制造商全称:Texas Instruments 功能描述:6-A 5-V/3.3-V Input Adjustable SWIFT Power Module |
| PT5408A | 功能描述:DC/DC转换器 2.5V 6A 3.3V Input Adj SWIFT Module RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| PT5408C | 功能描述:DC/DC转换器 2.5V 6A 3.3V Input Adj SWIFT Module RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| PT5408N | 功能描述:DC/DC转换器 2.5V 6A 3.3V Input Adj SWIFT Module RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| PT5410 | 制造商:Pulse Electronics Corporation 功能描述:- Bulk |
发布紧急采购，3分钟左右您将得到回复。