For technical support and more information, see inside back cover or visit www.ti.com/powertrends
Standard Application
PT6702—3.3V
The PT6702 is 13Amp fully integrated
switching regulator housed in a unique, space-
saving package. The PT6702 operates from
+3.3V input to provide a high-performance,
low-voltage power source for the industry’s
latest Ps, DSPs, and bus drivers.
The output is programmable from 1.3V to
2.05V with a 4-bit input, compatible with
Intel’s Pentium II Processor.
The PT6702 has short circuit protection,
a “Power Good” output, and an over-voltage
protection (OVP) drive output.
+3.3V Input
4-bit Programmable:
1.3V to 2.05V
High Efficiency
Differential Remote Sense
Short Circuit Protection
Over-Voltage Drive
Power Good Signal
Space Saving SIP Package
Solderable Copper Case
Cin = Required 1000F electrolytic
Cout= Required 330F electrolytic
L1 = Optional 1H input choke
R1 = Required 10k
pull-up when using Pwr Good signal. Pwr good
output is high when the output voltage is within specification.
Specifications
Characteristics
PT6702 SERIES
(T
a = 25°C unless noted)
Symbols
Conditions
Min
Typ
Max
Units
Output Current
Io
Ta = +60°C, 200 LFM, pkg N
0.1 (1)
—
13.0
A
Ta = +25°C, natural convection
0.1 (1)
—
13.0
Input Voltage Range
Vin
0.1A
≤ Io ≤ 13.0A
3.1 (2)
—
3.6
V
Output Voltage Tolerance
Vo
Vin = +3.3V, Io = 13.0A
Vo-0.03
—
Vo+0.03
V
–40°C
≤ Ta ≤ +85°C
Line Regulation
Regline
3.1V
≤ Vin ≤ 3.6V, Io = 13.0A
—
±10
—
mV
Load Regulation
Regload
Vin = +3.3V, 0.1 ≤ Io ≤ 13.0A
—
±20
—
mV
Vo Ripple/Noise
Vn
Vin = +3.3V, Io = 13.0A
—
50
—
mV
Transient Response
ttr
Io step between 6A and 12A
—
50
—
Sec
with Cout = 330F
Vos
Vo over/undershoot
—
100
—
mV
Efficiency
η
Vin = +3.3V, Io = 8A
Vo = 1.8V
—
86
—
%
Vo = 1.5V
—
84
—
%
Switching Frequency
o
3.1V
≤ Vin ≤ 3.6V
300
350
400
kHz
0.1A
≤ Io ≤ 13.0A
Absolute Maximum
Ta
Over Vin and Io Ranges
–40 (3)
—
+85 (4)
°C
Operating Temperature Range
Storage Temperature
Ts
—
–40
—
+125
°C
Mechanical Shock
Per Mil-STD-883D, Method 2002.3
1 msec, Half Sine, mounted to a fixture
—
500
—
G’s
Mechanical Vibration
Per Mil-STD-883D, Method 2007.2,
—15
—
G’s
20-2000 Hz, Soldered in a PC board
Weight
—
26
—
grams
Notes: (1) ISR-will operate down to no load with reduced specifications.
(2) The minimum input voltage is 3.1V or Vout+1.1V, whichever is greater.
(3) For operation below 0°C, Cin and Cout must have stable characteristics. Use either low ESR tantalum or Oscon capacitors.
(4) See Safe Operating Area curves.
(5) If the remote sense ground is not used, pin 7 must be connected to pin 8 for optimal output voltage accuracy.
Output Capacitors: The PT6702 requires a minimum ouput capacitance of 330F for proper operation. The maximum allowable output capacitance is 15,000F.
Input Filter: An input filter is optional for most applications. The input inductor must be sized to handle 10.0ADC with a typical value of 1H. The input capacitance must
be rated for a minimum of 2.0Arms of ripple current. For transient or dynamic load applications, additional capacitance may be required.
SLTS070A
(Revised 10/31/2000)
PT6702
10 - 12
14 - 18
19 - 22
2
V
IN
GND
1H
GND
V
OUT
C
OUT
+
C
IN
+
13
23
3
L1
PWR GOOD
LOAD
REMOTE SENSE (+)
REMOTE SENSE (-)
VID1
VID2
VID3
PROGRAMMING PINS
4
5
6
STBY*
8
VID0
OVP DRV
1
R1
13 Amp Programmable
Integrated Switching Regulator
Patent pending on package assembly
New Space-Saving
Package
PT6700 Product Family
Input
Vout
OVP/
Requires
Voltage
Adjust
Pwr Good
+12V Bias
PT6701
5V
VID
3
PT6702
3.3V
VID
3
PT6705
5V
Resistor
3
PT6715
5V
Resistor
PT6721
12V
VID
3
PT6725
12V
Resistor