- 您现在的位置：买卖IC网 > PDF目录96796 > PT7722C SWITCHING REGULATOR, SMA27 PDF资料下载
参数资料
| 型号： | PT7722C |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING REGULATOR, SMA27 |
| 封装： | HORIZONTAL SMT, SIP-27 |
| 文件页数： | 3/3页 |
| 文件大小： | 203K |
| 代理商： | PT7722C |
For assistance or to order, call (800) 531-5782
3
Power Trends, Inc. 27715 Diehl Road, Warrenville, IL 60555 (800) 531-5782 Fax: (630) 393-6902 http://www.powertrends.com
Applicatio n
Note s
PT7720 Series
Pin-Coded Output Voltage Adjustment on the
“Big Hammer II” Series ISRs
Power Trends PT7720 series ISRs incorporate pin-coded volt-
age control to adjust the ouput voltage. The control pins are
identified VID0 - VID4 (pins 1, 2, 3, 4, & 6) respectively.
When the control pins are left open-circuit, the ISR output will
regulate at its factory trimmed output voltage. Each pin is inter-
nally connected to a precision resistor, which when grounded
changes the output voltage by a set amount. By selectively
grounding VID0 -VID4, the output voltage of each ISR in the
PT7720 series ISRs can be programmed in incremental steps
over its specified output voltage range. The output voltage
ranges offered by these regulators provide a convenient method
of output voltage selection for many applications. In addition,
the program code and output voltage range of the PT7721
model ISR is compatible with the voltage ID specification de-
fined by Intel Corporation for voltage regulator modules
(VRMs) used to power Pentium microprocessors. Refer to
Figure 1 below for the connection schematic, and the PT7720
Data Sheet for the appropriate programming code information.
Notes:
1. The programming convention is as follows:-
Logic 0:
Connect to pin12 (Remote Sense Ground).
Logic 1:
Open circuit/open drain (See notes 2, & 4)
2. Do not connect pull-up resistors to the voltage program-
ming pins.
3. To minimize output voltage error, always use pin 12 (Re-
mote Sense Ground) as the logic “0” reference. While the
regular ground (pins 13-19) can also be used for program-
Figure 1
ming, doing so will degrade the load reglation of the prod-
uct.
4. If active devices are used to ground the voltage control pins,
low-level open drain MOSFET devices should be used over
bipolar transistors. The inherent Vce(sat) in bipolar devices
introduces errors in the device’s internal divider network.
Discrete transistors such as the BSS138, 2N7002,
IRLML2402, or the 74C906 hex open-drain buffer are
examples of appropriate devices.
Active Voltage Programming:
Special precautions should be taken when making changes to the
voltage control progam code while the unit is powered. It is
highly recommended that the ISR be either powered down or
held in standby. Changes made to the program code while Vout
is enabled induces high current transients through the device.
This is the result of the electrolytic output capacitors being ei-
ther charged or discharged to the new output voltage set-point.
The transient current can be minimized by making only incre-
mental changes to the binary code, i.e. one LSB at a time. A
minimum of 100s settling time between each program state is
also recommended. Making non-incremental changes to VID3
and VID4 with the output enabled is discouraged. If they are
changed, the transients induced can overstress the device result-
ing in a permanent drop in efficiency. If the use of active devices
prevents the program code being asserted prior to power-up,
pull pin 5 (STBY) to the device GND during the period that the
input voltage is applied to Vin. Releasing pin 5 will then allow
the device output to execute a soft-start power-up to the pro-
grammed voltage.
Cout
+
Cin
+
1
H
(Optional)
+12V
COM
STBY
L
O
A
D
PT7720
6
4
3
2
1
26
20-25
12
5
13-19
27
7-11
Vo
Vin
GND
SNS(+)
SNS(-)
Synch
Out
STBY
VID4 - VID0
相关PDF资料 |
PDF描述 |
|---|---|
| PT7721N | SWITCHING REGULATOR, SMA27 |
| PT7722A | SWITCHING REGULATOR, SMA27 |
| PT7722N | SWITCHING REGULATOR, SMA27 |
| PT7721A | SWITCHING REGULATOR, SMA27 |
| PT7722A | 17 A SWITCHING REGULATOR, 400 kHz SWITCHING FREQ-MAX, MSMA27 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PT7722N | 功能描述:DC/DC转换器 4.5-7.6Vout 17Amp 12 Vin Programmable ISR RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| PT7740 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:32Amp ＇Current Booster＇ for the PT7778 Regulator |
| PT7740A | 功能描述:REGULATR 32A BSTR FOR PT7778 HRZ RoHS:否 类别:电源 - 板载 >> DC DC Converters 系列:PT7740 标准包装:10 系列:PT4570 类型:隔离 输出数:1 电压 - 输入（最小）:36V 电压 - 输入（最大）:75V Voltage - Output 1:9V Voltage - Output 2:- Voltage - Output 3:- 电流 - 输出（最大）:3.3A 电源（瓦） - 制造商系列:30W 电压 - 隔离:1.5kV（1500V） 特点:- 安装类型:表面贴装 封装/外壳:19-SIP SMD 模块 尺寸/尺寸:3.00" L x 1.19" W x 0.50" H（76.2mm x 30.2mm x 12.7mm） 包装:托盘 工作温度:-40°C ~ 85°C 效率:84% 电源（瓦特）- 最大:30W |
| PT7740C | 功能描述:REGULATR 32A BSTR FOR PT7778 SMD RoHS:否 类别:电源 - 板载 >> DC DC Converters 系列:PT7740 标准包装:10 系列:PT4570 类型:隔离 输出数:1 电压 - 输入（最小）:36V 电压 - 输入（最大）:75V Voltage - Output 1:9V Voltage - Output 2:- Voltage - Output 3:- 电流 - 输出（最大）:3.3A 电源（瓦） - 制造商系列:30W 电压 - 隔离:1.5kV（1500V） 特点:- 安装类型:表面贴装 封装/外壳:19-SIP SMD 模块 尺寸/尺寸:3.00" L x 1.19" W x 0.50" H（76.2mm x 30.2mm x 12.7mm） 包装:托盘 工作温度:-40°C ~ 85°C 效率:84% 电源（瓦特）- 最大:30W |
| PT7740N | 功能描述:REGULATR 32A BSTR FOR PT7778 VRT RoHS:否 类别:电源 - 板载 >> DC DC Converters 系列:PT7740 标准包装:10 系列:PT4570 类型:隔离 输出数:1 电压 - 输入（最小）:36V 电压 - 输入（最大）:75V Voltage - Output 1:9V Voltage - Output 2:- Voltage - Output 3:- 电流 - 输出（最大）:3.3A 电源（瓦） - 制造商系列:30W 电压 - 隔离:1.5kV（1500V） 特点:- 安装类型:表面贴装 封装/外壳:19-SIP SMD 模块 尺寸/尺寸:3.00" L x 1.19" W x 0.50" H（76.2mm x 30.2mm x 12.7mm） 包装:托盘 工作温度:-40°C ~ 85°C 效率:84% 电源（瓦特）- 最大:30W |
发布紧急采购，3分钟左右您将得到回复。