参数资料
型号: PTB48540CAS
厂商: TEXAS INSTRUMENTS INC
元件分类: 电源模块
英文描述: 1-OUTPUT 10 W DC-DC REG PWR SUPPLY MODULE
文件页数: 8/12页
文件大小: 219K
代理商: PTB48540CAS
Application Notes
For technical support and further information visit http://power.ti.com
PTB48540 Series
Operating Features of the PTB48540
Series Power-Over-Ethernet Modules
Overview
Figure 1-1 shows the block diagram of the PTB48540
series of Power-over-Ethernet (PoE) modules. Input
power to the module can be supplied through either the
Data Line A/B or Spare Line A/B associated Ethernet
connections. A diode bridge associated with each of these
input pairs allows the input source to be supplied in ei-
ther polarity. A transient suppressor, located across the
common output of the diode bridges, protects the module
against power surges.
The input power to the internal DC/DC converter is
controlled by the TPS2375 IC. This IC is a power inter-
face switch, specifically designed for use with PoE powered
devices. The IC provides the device detection, classification,
and current limiting control that is necessary for a powered
device (PD) to comply with the IEEE 802.af Standard.
The DC/DC converter input circuit includes an EMI
filter, which maintains the module in compliance with
CISPR 22 (EN5022); class ‘B’ for radiated, and class ‘A’
for conducted emissions.
Data Line A
Data Line B
Spare Line A
Spare Line B
DC/DC
Converter
Detect B
Detect A
Class B
Class A
1
2
3
45
6
7
8
ILIM
CLASS
DETECT
VEE
EN_DC
RTN
NC
VDD
Inhibit
+VIN
–VIN
+VOUT
Adjust
VOUT Adj
+ VOUT
–VOUT
5
6
10
9
8
7
11
12
13
2
3
1
TPS2375
PoE Interface
1500 VDC
Isolation
4
Input Ref
Class Select
4.42 k
(Class 0)
PD Detect
24.9 k
(Valid Device)
–VOUT
External
RDETECT
External
RCLASS
Input EMI Filter
Output Inhibit
Figure 1 1; Block Diagram of the PTB48540 Series Modules
PD Detection
Prior to power up, the PoE power sourcing equipment
(PSE) must detect a 24.9-k
“discovery” load resistance
from the PD. This default value of resistance is neces-
sary for the PD to be recognized as a “valid device” by
the PSE. A 24.9-k
resistor is provided internally to the
PTB48540 modules. It is located across the ‘Detect A’
(pin 5) and ‘Detect B’ (pin 6) terminals. By placing an
external resistor across these pins (in parallel with the
internal 24.9-k
resistor), the module can be made to
communicate a “non-valid device” signature to the PSE.
A non-valid device is recognized by a resistance of less than
12 k
. Connecting a 16.9-k external resistor between
the ‘Detect A’ and ‘Detect B’ pins creates an equivalent
resistance of 10 k
. This is sufficient to communicate a
non-valid device signature. The external resistor should
not be less than 16.9 k
as this increases power dissipa-
tion in the power interface IC.
PD Classification Signature
The PSE uses a classification current to determine the
maximum supply current that the PD is allowed to draw.
The classification current is sensed by the PSE when the
supply voltage to the PD is between 15 V and 20 V. The
classification current is set on the PTB48540 by a pro-
gramming resistance. Table 1-1 gives the resistance values
相关PDF资料
PDF描述
PTB48540BAH 1-OUTPUT 10 W DC-DC REG PWR SUPPLY MODULE
PTB48540BAS 1-OUTPUT 10 W DC-DC REG PWR SUPPLY MODULE
PTB48540CAZ 1-OUTPUT 10 W DC-DC REG PWR SUPPLY MODULE
PTB48540AAZ 1-OUTPUT 10 W DC-DC REG PWR SUPPLY MODULE
PTB48540AAS 1-OUTPUT 10 W DC-DC REG PWR SUPPLY MODULE
相关代理商/技术参数
参数描述
PTB48540CAZ 功能描述:DC/DC转换器 12 V 10-W Pwr-Over- Ethernet Pwr Module RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压(标称): 输出端数量:1 输出电压(通道 1):3.3 V 输出电流(通道 1):600 mA 输出电压(通道 2): 输出电流(通道 2): 安装风格:SMD/SMT 封装 / 箱体尺寸:
PTB48550AAH 制造商:Rochester Electronics LLC 功能描述:- Bulk
PTB48550BAH 制造商:Rochester Electronics LLC 功能描述: 制造商:Texas Instruments 功能描述:
PTB48550CAH 制造商:Texas Instruments 功能描述:
PTB48550DAH 制造商:Texas Instruments 功能描述: