参数资料
型号: PTGL12AR1R2M1B54B0
厂商: Murata Electronics North America
文件页数: 92/105页
文件大小: 0K
描述: THERMISTOR
标准包装: 100
系列: Posistor®
在 25°C 时的电阻(欧姆): 1.2
电阻公差: ±20%
工作温度: -10°C ~ 60°C
功率 - 最大: 1.9W
安装类型: 通孔
封装/外壳: 圆盘形, 12.0mm 直径 x 4.0mm W
包装: 散装
! Note ? Please read rating and ! CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
? This catalog has only typical speci?cations. Therefore, please approve our product speci?cations or transact the approval sheet for product speci?cations before ordering.
! Caution/Notice
c Notice (Soldering and Mounting) PRG18/21 Series
1. Solder and Flux
R90E.pdf
Mar.4,2014
(1) Solder Paste
Use solder paste Sn:Pb=63:37wt%.
For your reference, we are using
63Sn/37Pb RMA9086 90-3-M18,
manufactured by Alpha Metals Japan Ltd.
96.5Sn/3.0Ag/0.5Cu M705-GRN360-K2-V,
manufactured by Senju Metal Industry Co., LTD for any
(2) Flux
Use rosin type flux in the soldering process.
If the flux below is used, some problems might be
caused in the product characteristics and reliability.
Please do not use these types of flux.
0.2wt%).
internal tests of this product.
(*Water-soluble flux can be defined as non-rosin type
flux including wash-type flux and non-wash-type flux.)
2. Cleaning Conditions
To remove the flux after soldering, observe the following
points in order to avoid deterioration of the characteristics
or any change to the external electrodes' quality.
Solvent
2-propanol
Dipping Cleaning
Less than 5 minutes
at room temp.
or
Less than 2 minutes
at 40?C max.
Ultrasonic Cleaning
Less than 1 minute
20W/L Frequency
of several 10kHz
to 100kHz.
Drying
After cleaning,
promptly dry
this product.
A sufficient cleaning should be applied to remove flux completely.
3. Soldering Conditions
In your mounting process, observe the following points in
order to avoid deterioration of the characteristics or
destruction of this product. The mounting quality of this
product may also be affected by the mounting conditions,
shown in the points below.
This product is for reflow soldering only. Flow soldering
should not be allowed.
(1) Printing Conditions of Solder Paste
(a) Standard thickness of solder paste printing should
be from 0.15 to 0.20 mm.
(b) After soldering, the solder fillet should be a height
from 0.2 mm to the thickness of this product (see the
figure at right).
(c) Too much solder result in excessive mechanical
stress to this product. Such stress may cause
E
Electrode
Solder
T
Solder
0.2mm V T V E
cracking or other mechanical damage. Also, it can
destroy the electrical performance of this product.
Continued on the following page.
90
相关PDF资料
PDF描述
1960-36-2 ALLIGATOR CLIP/SPADE LUG RED 36"
CR6612-500 TRANSDCR FREQ AC 0-5VDC OUT
1960-36-0 ALLIGATOR CLIP/SPADE LUG BLK 36"
6542J-48 SELF ADHESIVE THERMOCOUPLE 48"
PTGL12AR1R2M2B51B0 THERMISTOR
相关代理商/技术参数
参数描述
PTGL12AR1R2M2B51B0 功能描述:热敏电阻 - PTC 1.2ohm +/-20% PTC Thermistor RoHS:否 制造商:Vishay 电阻:1.5 kOhms 容差:1 % 端接类型:Radial 系列:TFPTL 工作温度范围:- 55 C to + 70 C
PTGL12AR270M9C01B0 功能描述:热敏电阻 - PTC 27ohm +/-20% PTC Thermistor RoHS:否 制造商:Vishay 电阻:1.5 kOhms 容差:1 % 端接类型:Radial 系列:TFPTL 工作温度范围:- 55 C to + 70 C
PTGL12AR5R6H4B71B0 功能描述:热敏电阻 - PTC 5.6ohm +/-25% PTC Thermistor RoHS:否 制造商:Vishay 电阻:1.5 kOhms 容差:1 % 端接类型:Radial 系列:TFPTL 工作温度范围:- 55 C to + 70 C
PTGL12ARR23N1C51B0 功能描述:热敏电阻 - PTC 0.23 Ohms 30% RoHS:否 制造商:Vishay 电阻:1.5 kOhms 容差:1 % 端接类型:Radial 系列:TFPTL 工作温度范围:- 55 C to + 70 C
PTGL12AS0R8K2B51A0 功能描述:热敏电阻 - PTC 0.8 Ohm 10% 30volt RoHS:否 制造商:Vishay 电阻:1.5 kOhms 容差:1 % 端接类型:Radial 系列:TFPTL 工作温度范围:- 55 C to + 70 C