- 您现在的位置：买卖IC网 > PDF目录98065 > PTH05T210WAST (TEXAS INSTRUMENTS INC) 1-OUTPUT DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | PTH05T210WAST |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 电源模块 |
| 英文描述： | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 封装： | PLASTIC, DIP-14 |
| 文件页数： | 3/31页 |
| 文件大小： | 1135K |
| 代理商： | PTH05T210WAST |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页
Ceramic Capacitors
Tantalum, Polymer-Tantalum Capacitors
Capacitor Table
Designing for Fast Load Transients
www.ti.com ...................................................................................................................................................... SLTS263I – AUGUST 2007 – REVISED MARCH 2009
Above 150 kHz the performance of aluminum electrolytic capacitors is less effective. Multilayer ceramic
capacitors have very low ESR and a resonant frequency higher than the bandwidth of the regulator. They can be
used to reduce the reflected ripple current at the input as well as improve the transient response of the output.
When used on the output their combined ESR is not critical as long as the total value of ceramic capacitors, with
values between 10 F and 100 F, does not exceed 5000 F (non-TurboTrans). In TurboTrans applications,
when ceramic capacitors are used on the output bus, total capacitance including bulk and ceramic types is not to
exceed 12,000
F.
Tantalum type capacitors are only used on the output bus, and are recommended for applications where the
ambient operating temperature is less than 0°C. The AVX TPS series and Kemet capacitor series are suggested
over many other tantalum types due to their higher rated surge, power dissipation, and ripple current capability.
As a caution, many general-purpose tantalum capacitors have higher ESR, reduced power dissipation, and lower
ripple current capability. These capacitors are also less reliable due to their reduced power dissipation and surge
current ratings. Tantalum capacitors that have no stated ESR or surge current rating are not recommended for
power applications.
Table 3 identifies the characteristics of capacitors from a number of vendors with acceptable ESR and ripple
current (rms) ratings. The recommended number of capacitors required at both the input and output buses is
identified for each capacitor type.
This is not an extensive capacitor list. Capacitors from other vendors are available with comparable
specifications. Those listed are for guidance. The RMS ripple current rating and ESR (at 100 kHz) are critical
parameters necessary to ensure both optimum regulator performance and long capacitor life.
The transient response of the dc/dc converter has been characterized using a load transient with a di/dt of
2.5A/s. The typical voltage deviation for this load transient is given in the Electrical Characteristics table using
the minimum required value of output capacitance. As the di/dt of a transient is increased, the response of a
converter’s regulation circuit ultimately depends on its output capacitor decoupling network. This is an inherent
limitation with any dc/dc converter once the speed of the transient exceeds its bandwidth capability.
If the target application specifies a higher di/dt or lower voltage deviation, the requirement can only be met with
additional low ESR ceramic capacitor decoupling. Generally, with 50% load steps at > 100A/
s, adding multiple
10
F ceramic capacitors, 3225 case size, plus 10×1F, including numerous high frequency ceramics (≤0.1F)
are all that is required to soften the transient higher frequency edges. Special attention is essential with regards
to location, types, and position of higher frequency ceramic and lower ESR bulk capacitors. DSP, FPGA and
ASIC vendors identify types, location and capacitance required for optimum performance of the high frequency
devices. The details regarding the PCB layout and capacitor/component placement are important at these high
frequencies. Low impedance buses and unbroken PCB copper planes with components located as close to the
high frequency processor are essential for optimizing transient performance. In many instances additional
capacitors may be required to insure and minimize transient aberrations.
Copyright 2007–2009, Texas Instruments Incorporated
11
Product Folder Link(s): PTH05T210W
相关PDF资料 |
PDF描述 |
|---|---|
| PTH05T210WAH | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTH05T210WAD | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTH05T210WAZT | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTH08000WAZT | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTH08T240FAS | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PTH05T210WAZ | 功能描述:DC/DC转换器 30A 4.5-5.5V-Input/ Wide-Out Adj Pwr Mdl RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| PTH05T210WAZT | 功能描述:DC/DC转换器 30A 4.5-5.5V-Input/ Wide-Out Adj Pwr Mdl RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| PTH08000W | 制造商:TI 制造商全称:Texas Instruments 功能描述:2.25-A, WIDE INPUT, ADJUSTABLE SWITCHING REGULATOR |
| PTH08000WAH | 功能描述:DC/DC转换器 2.25A 5/12V Input WideAdj Module RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| PTH08000WAH | 制造商:Texas Instruments 功能描述:MODULE PIP .9-5.5V 2.25A HORZ TH 制造商:Texas Instruments 功能描述:MODULE PIP .9-5.5V 2.25A HORZ TH; Primary Input Voltage:14V; No. of Outputs:1; Output Voltage:5.5V; Output Current:2.25A; Voltage Regulator Case Style:Thru Hole Module; No. of Pins:6; Operating Temperature Min:-40C; Operating ;RoHS Compliant: Yes |
发布紧急采购，3分钟左右您将得到回复。