- 您现在的位置：买卖IC网 > PDF目录69254 > PTH08T221WAZ (TEXAS INSTRUMENTS INC) 1-OUTPUT DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | PTH08T221WAZ |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 电源模块 |
| 英文描述： | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 封装： | ROHS COMPLIANT, PLASTIC, DIP-11 |
| 文件页数： | 6/38页 |
| 文件大小： | 1290K |
| 代理商： | PTH08T221WAZ |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
Output Capacitor (Required)
Output Capacitor Information
TurboTrans Output Capacitance
Non-TurboTrans Output Capacitance
SLTS252K – NOVEMBER 2005 – REVISED JUNE 2009................................................................................................................................................... www.ti.com
The PTH08T221W requires a minimum output capacitance of 300
F of ceramic type.
The PTH08T220W requires a minimum output capacitance of 220
F of aluminum, polymer-aluminum, tantulum,
or polymer-tantalum type.
The required capacitance above the minimum will be determined by actual transient deviation requirements. See
the TurboTrans Technology application section within this document for specific capacitance selection.
When selecting output capacitors, the main considerations are capacitor type, temperature stability, and ESR.
When using the TurboTrans feature, the capacitance X ESR product should also be considered (see the
following section).
Ceramic output capacitors added for high-frequency bypassing should be located as close as possible to the
load to be effective. Ceramic capacitor values below 10
F should not be included when calculating the total
output capacitance value.
When the operating temperature is below 0°C, the ESR of aluminum electrolytic capacitors increases. For these
applications, OS-CON, poly-aluminum, and polymer-tantalum types should be considered.
TurboTrans allows the designer to optimize the output capacitance according to the system transient design
requirement. High quality, ultra-low ESR capacitors are required to maximize TurboTrans effectiveness. When
using TurboTrans, the capacitor's capacitance (
F) × ESR (m) product determines its capacitor type; Type A,
B, or C. These three types are defined as follows:
Type A = (100
≤ capacitance × ESR ≤ 1000) (e.g. ceramic)
Type B = (1000 < capacitance × ESR
≤ 5000) (e.g. polymer-tantalum)
Type C = (5000 < capacitance × ESR
≤ 10,000) (e.g. OS-CON)
When using more than one type of output capacitor, select the capacitor type that makes up the majority of your
total output capacitance. When calculating the C×ESR product, use the maximum ESR value from the capacitor
manufacturer's datasheet.
The PTH08T221W should be used when only Type A (ceramic) capacitors are used on the output.
Working Examples:
A capacitor with a capacitance of 330
F and an ESR of 5m, has a C×ESR product of 1650Fxm (330F ×
5m
). This is a Type B capacitor. A capacitor with a capacitance of 1000
F and an ESR of 8m, has a C×ESR
product of 8000
Fxm (1000F × 8m). This is a Type C capacitor.
See the TurboTrans Technology application section within this document for specific capacitance selection.
Table 3 includes a preferred list of capacitors by type and vendor. See the Output Bus / TurboTrans column.
If the TurboTrans feature is not used, minimum ESR and maximum capacitor limits must be followed. System
stability may be effected and increased output capacitance may be required without TurboTrans.
When using the PTH08T220W, observe the minimum ESR of the entire output capacitor bank. The minimum
ESR limit of the output capacitor bank is 7m
. A list of preferred low-ESR type capacitors, are identified in
When using the PTH08T221W without the TurboTrans feature, the maximum amount of capacitance is 3000
F
of ceramic type. Large amounts of capacitance may reduce system stability.
Utilizing the TurboTrans feature improves system stability, improves transient response, and reduces the
amount of output capacitance required to meet system transient design requirements.
14
Copyright 2005–2009, Texas Instruments Incorporated
Product Folder Link(s): PTH08T220W PTH08T221W
相关PDF资料 |
PDF描述 |
|---|---|
| PTH08T220WAH | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTH08T221WAD | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTH08T220WAZ | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTH08T221WAS | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTH08T221WAST | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PTH08T221WAZT | 功能描述:DC/DC转换器 16A 4.5V to 14V Inp Ceramic Cap Version RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| PTH08T230W | 制造商:TI 制造商全称:Texas Instruments 功能描述:6-A, 4.5-V to 14-V INPUT, NON-ISOLATED, WIDE-OUTPUT, ADJUSTABLE POWER MODULE WITH TurboTrans |
| PTH08T230W_07 | 制造商:TI 制造商全称:Texas Instruments 功能描述:6-A, 4.5-V to 14-V INPUT, NON-ISOLATED, WIDE-OUTPUT, ADJUSTABLE POWER MODULE WITH TurboTrans⑩ |
| PTH08T230WAD | 功能描述:DC/DC转换器 6A 2.2-5.5V Input Non Isolated POL RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| PTH08T230WAS | 功能描述:DC/DC转换器 6A 2.2-5.5V Input Non Isolated POL RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
发布紧急采购，3分钟左右您将得到回复。