- 您现在的位置：买卖IC网 > PDF目录69254 > PTH08T230WAST (TEXAS INSTRUMENTS INC) 1-OUTPUT DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | PTH08T230WAST |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 电源模块 |
| 英文描述： | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 封装： | ROHS COMPLIANT |
| 文件页数： | 7/39页 |
| 文件大小： | 1281K |
| 代理商： | PTH08T230WAST |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页
www.ti.com
SLTS265K – NOVEMBER 2005 – REVISED JUNE 2010
Output Capacitor (Required)
The PTH08T231W requires a minimum output capacitance of 200 mF of ceramic type.
The PTH08T230W requires a minimum output capacitance of 200 mF ceramic type. An optional 100 mF of
non-ceramic,
low-ESR
capacitance
is
recommended
for
improved
performance.
See
the
Electrical
Characteristics table for maximum capacitor limits.
The required capacitance above the minimum will be determined by actual transient deviation requirements. See
the TurboTrans Technology application section within this document for specific capacitance selection.
Output Capacitor Information
When selecting output capacitors, the main considerations are capacitor type, temperature stability, and ESR.
When using the TurboTrans feature, the capacitance x ESR product should also be considered (see the following
section).
Ceramic output capacitors added for high-frequency bypassing should be located as close as possible to the
load to be effective. Ceramic capacitor values below 10 mF should not be included when calculating the total
output capacitance value.
When the operating temperature is below 0°C, the ESR of aluminum electrolytic capacitors increases. For these
applications, OS-CON, poly-aluminum, and polymer-tantalum types should be considered.
TurboTrans Output Capacitance
TurboTrans allows the designer to optimize the output capacitance according to the system transient design
requirement. High quality, ultra-low ESR capacitors are required to maximize TurboTrans effectiveness. When
using TurboTrans, the capacitor's capacitance (in mF) × ESR (in m) product determines its capacitor type; Type
A, B, or C. These three types are defined as follows:
Type A = (100
≤ capacitance × ESR ≤ 1000) (e.g. ceramic)
Type B = (1000 < capacitance × ESR
≤ 5000) (e.g. polymer-tantalum)
Type C = (5000 < capacitance × ESR
≤ 10,000) (e.g. OS-CON)
When using more than one type of output capacitor, select the capacitor type that makes up the majority of your
total output capacitance. When calculating the C × ESR product, use the maximum ESR value from the capacitor
manufacturer's data sheet.
Working Examples:
A capacitor with a capacitance of 330 mF and an ESR of 5 m, has a C × ESR product of 1650 mF x m (330 ×
5). This is a Type B capacitor. A capacitor with a capacitance of 1000 mF and an ESR of 8 m, has a C × ESR
product of 8000 mF x m (1000 × 8). This is a Type C capacitor.
See the TurboTrans Technology application section within this document for specific capacitance selection.
Table 3 includes a preferred list of capacitors by type and vendor. See the Output Bus / TurboTrans column.
Non-TurboTrans Output Capacitance
If the TurboTrans feature is not used, minimum ESR and maximum capacitor limits must be followed. System
stability may be effected and increased output capacitance may be required without TurboTrans.
When using the PTH08T230W without the TurboTrans feature, observe the minimum ESR of the entire output
capacitor bank. The minimum ESR limit of the output capacitor bank is 7 m
. A list of preferred low-ESR type
capacitors, are identified in Table 3. Large amounts of capacitance may reduce system stability when not using
the TurboTrans feature.
When using the PTH08T231W without the TurboTrans feature, the maximum amount of capacitance is 5000 mF
of ceramic type. Large amounts of capacitance may reduce system stability.
Using the TurboTrans feature improves system stability, improves transient response, and reduces the
amount of output capacitance required to meet system transient design requirements.
Copyright 2005–2010, Texas Instruments Incorporated
15
Product Folder Link(s): PTH08T230W PTH08T231W
相关PDF资料 |
PDF描述 |
|---|---|
| PTH08T230WAS | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTH08T230WAD | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTH08T231WAZT | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTH08T240FAH | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTH08T241WAZT | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PTH08T230WAZ | 功能描述:DC/DC转换器 6A 2.2-5.5V Input Non Isolated POL RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| PTH08T230WAZT | 功能描述:DC/DC转换器 6A 2.2-5.5V Input Non Isolated POL RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| PTH08T231W | 制造商:TI 制造商全称:Texas Instruments 功能描述:6-A, 4.5-V to 14-V INPUT, NON-ISOLATED, WIDE-OUTPUT, ADJUSTABLE POWER MODULE WITH TurboTrans⑩ |
| PTH08T231WAD | 功能描述:DC/DC转换器 6A 4.5V-14Vin Cer Cap Adj Pwr Module RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| PTH08T231WAS | 功能描述:DC/DC转换器 6A 4.5V-14Vin Cer Cap Adj Pwr Module RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
发布紧急采购，3分钟左右您将得到回复。