- 您现在的位置：买卖IC网 > PDF目录69254 > PTH08T231WAZ (TEXAS INSTRUMENTS INC) 1-OUTPUT DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | PTH08T231WAZ |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 电源模块 |
| 英文描述： | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 封装： | ROHS COMPLIANT PACKAGE-10 |
| 文件页数： | 17/39页 |
| 文件大小： | 1281K |
| 代理商： | PTH08T231WAZ |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页
t-Time=4ms/div
I (2 A/div)
I
V (5V/div)
I
V
(2V/div)
O
PTH08T230W
Track
GND
3
2
C
I
V
I
V
I
SLTS265K – NOVEMBER 2005 – REVISED JUNE 2010
www.ti.com
Soft-Start Power Up
The Auto-Track feature allows the power-up of multiple PTH/PTV modules to be directly controlled from the
Track pin. However in a stand-alone configuration, or when the Auto-Track feature is not being used, the Track
Figure 20. Defeating the Auto-Track Function
Figure 21. Power-Up Waveform
When the Track pin is connected to the input voltage the Auto-Track function is permanently disengaged. This
allows the module to power up entirely under the control of its internal soft-start circuitry. When power up is
under soft-start control, the output voltage rises to the set-point at a quicker and more linear rate. From the
moment a valid input voltage is applied, the soft-start control introduces a short time delay (typically 2 ms–10 ms)
before allowing the output voltage to rise. The output then progressively rises to the module’s setpoint voltage.
Figure 21 shows the soft-start power-up characteristic of the PTH08T230W operating from a 12-V input bus and
configured for a 3.3-V output. The waveforms were measured with a 6-A constant current load and the
Auto-Track feature disabled. The initial rise in input current when the input voltage first starts to rise is the charge
current drawn by the input capacitors. Power-up is complete within 20 ms.
Overcurrent Protection
For protection against load faults, all modules incorporate output overcurrent protection. Applying a load that
exceeds the regulator's overcurrent threshold causes the regulated output to shut down. Following shutdown, a
module periodically attempts to recover by initiating a soft-start power-up. This is described as a hiccup mode of
operation, whereby the module continues in a cycle of successive shutdown and power up until the load fault is
removed. During this period, the average current flowing into the fault is significantly reduced. Once the fault is
removed, the module automatically recovers and returns to normal operation.
Overtemperature Protection (OTP)
A thermal shutdown mechanism protects the module’s internal circuitry against excessively high temperatures. A
rise in the internal temperature may be the result of a drop in airflow, or a high ambient temperature. If the
internal temperature exceeds the OTP threshold, the module’s Inhibit control is internally pulled low. This turns
the output off. The output voltage drops as the external output capacitors are discharged by the load circuit. The
recovery is automatic, and begins with a soft-start power up. It occurs when the sensed temperature decreases
by about 10°C below the trip point.
The overtemperature protection is a last resort mechanism to prevent thermal stress to the regulator.
Operation at or close to the thermal shutdown temperature is not recommended and reduces the long-term
reliability of the module. Always operate the regulator within the specified safe operating area (SOA) limits for
the worst-case conditions of ambient temperature and airflow.
24
Copyright 2005–2010, Texas Instruments Incorporated
Product Folder Link(s): PTH08T230W PTH08T231W
相关PDF资料 |
PDF描述 |
|---|---|
| PTH08T230WAST | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTH08T230WAS | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTH08T230WAD | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTH08T231WAZT | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTH08T240FAH | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PTH08T231WAZT | 功能描述:DC/DC转换器 6A 4.5V-14Vin Cer Cap Adj Pwr Module RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| PTH08T240F | 制造商:TI 制造商全称:Texas Instruments 功能描述:10-A, 4.5-V to 14-V INPUT, NON-ISOLATED POWER MODULE FOR 3-GHz DSP SYSTEMS |
| PTH08T240F_08 | 制造商:TI 制造商全称:Texas Instruments 功能描述:10-A, 4.5-V to 14-V INPUT, NON-ISOLATED POWER MODULE FOR 3-GHz DSP SYSTEMS |
| PTH08T240FAD | 功能描述:DC/DC转换器 10-A 4.5-14V Input Pwr Module RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| PTH08T240FAS | 功能描述:DC/DC转换器 10-A 4.5-14V Input Pwr Module RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
发布紧急采购，3分钟左右您将得到回复。