- 您现在的位置：买卖IC网 > PDF目录69254 > PTH08T255WAD (TEXAS INSTRUMENTS INC) DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | PTH08T255WAD |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 电源模块 |
| 英文描述： | DC-DC REG PWR SUPPLY MODULE |
| 封装： | PLASTIC, MODULE-22 |
| 文件页数： | 2/34页 |
| 文件大小： | 4336K |
| 代理商： | PTH08T255WAD |
第1页当前第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
Output Capacitor (Required)
Output Capacitor Information
TurboTrans Output Capacitance
Non-TurboTrans Output Capacitance
SLTS290 – NOVEMBER 2008 ........................................................................................................................................................................................... www.ti.com
The PTH08T255W requires a minimum output capacitance of 1000F of polymer-aluminum, tantulum, or
polymer-tantalum type. Ceramic output capacitance can be used in addition to the required non-ceramic type.
The required capacitance above the minimum is determined by actual transient deviation requirements. See the
TurboTrans Technology application section within this document for specific capacitance selection.
When selecting output capacitors, the main considerations are capacitor type, temperature stability, and ESR.
When using the TurboTrans feature, the capacitance × ESR product should also be considered (see the
following section).
Ceramic output capacitors added for high-frequency bypassing should be located as close as possible to the
load to be effective. Ceramic capacitor values below 10F should not be included when calculating the total
output capacitance value.
When the operating temperature is below 0°C, the ESR of aluminum electrolytic capacitors increases. For these
applications, OS-CON, poly-aluminum, and polymer-tantalum types should be considered.
TurboTrans allows the designer to optimize the output capacitance according to the system transient design
requirement. High quality, ultra-low ESR capacitors are required to maximize TurboTrans effectiveness. When
using TurboTrans, the capacitor's capacitance (F) × ESR (m
) product determines its capacitor type; Type A,
B, or C. These three types are defined as follows:
Type A = (100
≤ capacitance × ESR ≤ 1000) (e.g. ceramic) (use Type A capacitors in addition to Type B or C)
Type B = (1000 < capacitance × ESR
≤ 5000) (e.g. polymer-tantalum)
Type C = (5000 < capacitance × ESR
≤ 10,000) (e.g. OS-CON)
When using more than one type of output capacitor, select the capacitor type that makes up the majority of your
total output capacitance. When calculating the C×ESR product, use the maximum ESR value from the capacitor
manufacturer's datasheet.
Working Examples:
A capacitor with a capacitance of 330F and an ESR of 5m
, has a C×ESR product of 1650Fxm (330F ×
5m
). This is a Type B capacitor. A capacitor with a capacitance of 1000F and an ESR of 8m, has a C×ESR
product of 8000Fxm
(1000F × 8m). This is a Type C capacitor.
See the TurboTrans Technology application section within this document for specific capacitance selection.
Table 3 includes a preferred list of capacitors by type and vendor. See the Output Bus / TurboTrans column.
If the TurboTrans feature is not used, minimum ESR and maximum capacitor limits must be followed. System
stability may be effected and increased output capacitance may be required without TurboTrans.
When using the PTH08T255W, observe the minimum ESR of the entire output capacitor bank. The minimum
ESR limit of the output capacitor bank is 7m
. A list of preferred low-ESR type capacitors, are identified in
When using the PTH08T255W without the TurboTrans feature, the maximum amount of capacitance is 1000 F
of ceramic type. Large amounts of capacitance may reduce system stability.
Utilizing the TurboTrans feature improves system stability, improves transient response, and reduces the
amount of output capacitance required to meet system transient design requirements.
10
Copyright 2008, Texas Instruments Incorporated
Product Folder Link(s): PTH08T255W
相关PDF资料 |
PDF描述 |
|---|---|
| PTH08T261WAD | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTH08T260WAST | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTH08T261WAST | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTH08T260WAD | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTH08T260WAZ | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PTH08T255WAS | 功能描述:DC/DC转换器 40A,8-14V In,3-5.25V Out,Non-Iso Pwr Mod RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| PTH08T255WAST | 功能描述:DC/DC转换器 40A,8-14V In,3-5.25V Out,Non-Iso Pwr Mod RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| PTH08T255WAZ | 功能描述:DC/DC转换器 40A,8-14V In,3-5.25V Out,Non-Iso Pwr Mod RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| PTH08T255WAZT | 功能描述:DC/DC转换器 40A,8-14V In,3-5.25V Out,Non-Iso Pwr Mod RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| PTH08T260W | 制造商:TI 制造商全称:Texas Instruments 功能描述:3-A, 4.5-V to 14-V INPUT, NON-ISOLATED, WIDE-OUTPUT, ADJUSTABLE POWER MODULE WITH TurboTrans |
发布紧急采购，3分钟左右您将得到回复。