- 您现在的位置：买卖IC网 > PDF目录20620 > PX3511ADDG-RA (Intersil)IC DRVR SYNC BUCK HF 10-DFN PDF资料下载
参数资料
| 型号： | PX3511ADDG-RA |
| 厂商： | Intersil |
| 文件页数： | 6/10页 |
| 文件大小： | 0K |
| 描述： | IC DRVR SYNC BUCK HF 10-DFN |
| 标准包装： | 6,000 |
| 配置： | 高端和低端，同步 |
| 输入类型： | PWM |
| 延迟时间： | 10ns |
| 电流 - 峰： | 1.25A |
| 配置数： | 1 |
| 输出数： | 2 |
| 高端电压 - 最大（自引导启动）： | 36V |
| 电源电压： | 10.8 V ~ 13.2 V |
| 工作温度： | 0°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-VFDFN 裸露焊盘 |
| 供应商设备封装： | 10-DFN（3x3） |
| 包装： | 带卷 (TR) |
PX3511A, PX3511B
Description
PWM
1.18V<PWM<2.36V
0.76V<PWM<1.96V
t PDHU
t PDLU
t PDTS
t TSSHD
t PDTS
UGATE
LGATE
t PDLL
t FL
t RU
t RL
t FU
t TSSHD
t PDHL
FIGURE 1. TIMING DIAGRAM
Operation
Designed for versatility and speed, the PX3511A and
PX3511B MOSFET drivers control both high-side and low-
side N-Channel FETs of a half-bridge power train from one
externally provided PWM signal.
Prior to VCC exceeding its POR level, the Pre-POR
overvoltage protection function is activated during initial
startup; the upper gate (UGATE) is held low and the lower
gate (LGATE), controlled by the Pre-POR overvoltage
protection circuits, is connected to the PHASE. Once the
VCC voltage surpasses the VCC Rising Threshold (See
Electrical Specifications), the PWM signal takes control of
gate transitions. A rising edge on PWM initiates the turn-off
of the lower MOSFET (see Timing Diagram). After a short
propagation delay [t PDLL ], the lower gate begins to fall.
Typical fall times [t FL ] are provided in the Electrical
Specifications section. Adaptive shoot-through circuitry
monitors the LGATE voltage and determines the upper gate
delay time [t PDHU ]. This prevents both the lower and upper
MOSFETs from conducting simultaneously. Once this delay
period is complete, the upper gate drive begins to rise [t RU ]
and the upper MOSFET turns on.
A falling transition on PWM results in the turn-off of the upper
MOSFET and the turn-on of the lower MOSFET. A short
propagation delay [t PDLU ] is encountered before the upper
gate begins to fall [t FU ]. Again, the adaptive shoot-through
circuitry determines the lower gate delay time, t PDHL . The
PHASE voltage and the UGATE voltage are monitored, and
the lower gate is allowed to rise after PHASE drops below a
level or the voltage of UGATE to PHASE reaches a level
depending upon the current direction (See next section for
details). The lower gate then rises [t RL ], turning on the lower
MOSFET.
6
Adaptive Zero Shoot-Through Deadtime Control
These drivers incorporate an adaptive deadtime control
technique to minimize deadtime, resulting in high efficiency
from the reduced freewheeling time of the lower MOSFETs’
body-diode conduction, and to prevent the upper and lower
MOSFETs from conducting simultaneously. This is
accomplished by ensuring either rising gate turns on its
MOSFET with minimum and sufficient delay after the other
has turned off.
During turn-off of the lower MOSFET, the LGATE voltage is
monitored until it drops below 1.75V, at which time the
UGATE is released to rise after 20ns of propagation delay.
Once the PHASE is high, the adaptive shoot-through
circuitry monitors the PHASE and UGATE voltages during a
PWM falling edge and the subsequent UGATE turn-off. If
either the UGATE falls to less than 1.75V above the PHASE
or the PHASE falls to less than +0.8V, the LGATE is
released to turn on.
Three-State PWM Input
A unique feature of these drivers and other Intersil drivers is
the addition of a shutdown window to the PWM input. If the
PWM signal enters and remains within the shutdown window
for a set holdoff time, the driver outputs are disabled and
both MOSFET gates are pulled and held low. The shutdown
state is removed when the PWM signal moves outside the
shutdown window. Otherwise, the PWM rising and falling
thresholds outlined in the ELECTRICAL SPECIFICATIONS
determine when the lower and upper gates are enabled.
This feature helps prevent a negative transient on the output
voltage when the output is shut down, eliminating the
Schottky diode that is used in some systems for protecting
the load from reversed output voltage events.
In addition, more than 400mV hysteresis also incorporates
into the three-state shutdown window to eliminate PWM
FN6462.0
February 26, 2007
相关PDF资料 |
PDF描述 |
|---|---|
| ADE7566ASTZF8 | IC ENERGY METER MCU 8K 64LQFP |
| GSM06DTBI | CONN EDGECARD 12POS R/A .156 SLD |
| AC244026 | EXTENSION PAK PIC16F727-ICE |
| ISL6610IBZ-T | IC MOSFET DRVR DUAL SYNC 14-SOIC |
| C1005C0G1H080C | CAP CER 8PF 50V NP0 0402 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PX3511B | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Advanced Synchronous Rectified Buck MOSFET Drivers with Protection Features |
| PX3511BDAG | 功能描述:IC DRVR SYNC BUCK HF 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - MOSFET，电桥驱动器 - 外部开关 系列:- 标准包装:6,000 系列:* |
| PX3511BDAG-R3 | 功能描述:IC DRVR SYNC BUCK HF 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - MOSFET，电桥驱动器 - 外部开关 系列:- 标准包装:6,000 系列:* |
| PX3511BDDG | 功能描述:IC DRVR SYNC BUCK HF 10-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - MOSFET，电桥驱动器 - 外部开关 系列:- 标准包装:50 系列:- 配置:高端 输入类型:非反相 延迟时间:200ns 电流 - 峰:250mA 配置数:1 输出数:1 高端电压 - 最大（自引导启动）:600V 电源电压:12 V ~ 20 V 工作温度:-40°C ~ 125°C 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-DIP 包装:管件 其它名称:*IR2127 |
| PX3511BDDG-RA | 功能描述:IC DRVR SYNC BUCK HF 10-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - MOSFET，电桥驱动器 - 外部开关 系列:- 标准包装:6,000 系列:* |
发布紧急采购，3分钟左右您将得到回复。