- 您现在的位置：买卖IC网 > Datasheet目录874 > Q48T08120-NBB0 (Power-One)DC/DC QTR BRICK 96W 12V T/H Datasheet资料下载
参数资料
| 型号： | Q48T08120-NBB0 |
| 厂商： | Power-One |
| 文件页数： | 6/14页 |
| 文件大小： | 0K |
| 描述： | DC/DC QTR BRICK 96W 12V T/H |
| 标准包装： | 50 |
| 系列： | * |
Q48T08120 DC-DC Converter Data Sheet
36-75 VDC Input; 12VDC @ 8A Output
When using remote sense, the output voltage at the con-
verter can be increased by as much as 10% above the
nominal rating in order to maintain the required voltage
across the load. Therefore, the designer must, if necessary,
R T ? DECR =
where,
511
?
? 10.22 [k ? ]
decrease the maximum current (originally obtained from the
Q Family
derating curves) by the same percentage to ensure the con-
verter’s actual output power remains at or below the maxi-
mum allowable output power.
Output Voltage Adjust /TRIM (Pin 6)
Vin
Vin (+)
ON/OFF
Vin (-)
TM
Converter
(Top View)
Vout (+)
SENSE (+)
TRIM
SENSE (-)
Vout (-)
R T-INCR
Rload
The converter’s output voltage can be adjusted up 10% or
down 20% relative to the rated output voltage by the addition
of an externally connected resistor. The output voltage can
be trimmed down to 8V, using the trim equations below,
without deteriorating electrical parameters and derating
plots. With 1% external trimming resistor, the output voltage
set point accuracy will be +/-1.6% (worst case).
The TRIM pin should be left open if trimming is not being
used. To minimize noise pickup, a 0.1 μ F capacitor is con-
nected internally between the TRIM and SENSE(-) pins.
To increase the output voltage, refer to Fig. 4. A trim resistor,
Fig. 4: Configuration for increasing output voltage .
R T ? DECR = Required value of trim-down resistor [k ? ]
and ? is as defined above.
Note: The above equations for calculation of trim resistor
values match those typically used in conventional industry-
standard quarter bricks.
Q Family
R T-INCR , should be connected between the TRIM (Pin 6) and
SENSE(+) (Pin 7), with a value of:
Vin (+)
TM
Converter
(Top View)
Vout (+)
SENSE (+)
R T ? INCR =
where,
5.11(100 + ? )V O ? NOM ? 626
1.225 ?
? 10.22 [k ? ]
Vin
ON/OFF
Vin (-)
TRIM
SENSE (-)
Vout (-)
R T-DECR
Rload
R T ? INCR = Required value of trim-up resistor k ? ]
V O ? NOM = Nominal value of output voltage [V]
Fig. 5: Configuration for decreasing output voltage.
? =
(V O - REQ ? V O - NOM )
V O - NOM
X 100 [%]
Trimming/sensing beyond 110% of the rated output voltage
is not an acceptable design practice, as this condition could
cause unwanted triggering of the output over-voltage protec-
tion (OVP) circuit. The designer should ensure that the dif-
V O ? REQ = Desired (trimmed) output voltage [V].
When trimming up, care must be taken not to exceed the
converter‘s maximum allowable output power. See previous
section for a complete discussion of this requirement.
To decrease the output voltage (Fig. 5), a trim resistor,
R T-DECR , should be connected between the TRIM (Pin 6) and
SENSE(-) (Pin 5), with a value of:
ference between the voltages across the converter’s output
pins and its sense pins does not exceed 1.20 V, or:
[V OUT ( + ) ? V OUT ( ? )] ? [V SENSE ( + ) ? V SENSE ( ? )] ≤ 1.20 [V]
This equation is applicable for any condition of output sens-
ing and/or output trim.
JUN 23, 2004 revised to NOV 20, 2006
Page 6 of 14
www.power-one.com
相关PDF资料 |
PDF描述 |
|---|---|
| Q48T25018-NBB0 | DC/DC QTR BRICK 45W 1.8V |
| Q48T25033-NBB0 | DC/DC QTR BRICK 83W 3.3V T/H |
| Q48T30015-NBB0 | CONV DC-DC 48V IN 1.5V OUT 45W |
| Q48T30018-NBA0 | DC/DC QTR BRICK 54W 1.8V T/H |
| Q48T30025-NDB0 | DC/DC QTR BRICK 75W 2.5V T/H |
相关代理商/技术参数 |
参数描述 |
|---|---|
| Q48T08120-NBB0G | 功能描述:DC/DC转换器 RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| Q48T08120-NBBP | 制造商:Power-One 功能描述:DCDC - Bulk |
| Q48T08120-NBBPG | 制造商:Power-One 功能描述:DCDC,HAZMAT - Bulk |
| Q48T08120-NBC0G | 制造商:Power-One 功能描述:Module DC-DC 1-OUT 12V 8A 8-Pin Quarter-Brick |
| Q48T08120-NBCP | 制造商:Power-One 功能描述:DCDC - Bulk |
发布紧急采购，3分钟左右您将得到回复。