- 您现在的位置：买卖IC网 > Datasheet目录874 > Q48T30018-NBA0 (Power-One)DC/DC QTR BRICK 54W 1.8V T/H Datasheet资料下载
参数资料
| 型号： | Q48T30018-NBA0 |
| 厂商： | Power-One |
| 文件页数： | 7/14页 |
| 文件大小： | 0K |
| 描述： | DC/DC QTR BRICK 54W 1.8V T/H |
| 标准包装： | 50 |
| 系列： | * |
Q48T30018 DC-DC Converter Data Sheet
36-75 VDC Input; 1.8 VDC @ 30A Output
Protection Features
Input Undervoltage Lockout
Input undervoltage lockout is standard with this converter.
The converter will shut down when the input voltage drops
below a pre-determined voltage.
The input voltage must be at least 35 V for the converter to
turn on. Once the converter has been turned on, it will shut
off when the input voltage drops below 31 V. This feature is
beneficial in preventing deep discharging of batteries used in
telecom applications.
Output Overcurrent Protection (OCP)
The converter is protected against overcurrent or short cir-
cuit conditions. Upon sensing an overcurrent condition, the
converter will switch to constant current operation and
thereby begin to reduce output voltage. When the output
voltage drops below 0.8 Vdc, the converter will shut down
(Fig. 26).
Once the converter has shut down, it will attempt to restart
nominally every 100 ms with a 3% duty cycle (Fig 27). The
attempted restart will continue indefinitely until the overload
or short circuit conditions are removed or the output voltage
rises above 0.8 Vdc.
Output Overvoltage Protection (OVP)
The converter will shut down if the output voltage across
Vout(+) (Pin 8) and Vout(-) (Pin 4) exceeds the threshold of
the OVP circuitry. The OVP circuitry contains its own refer-
ence, independent of the output voltage regulation loop.
Once the converter has shut down, it will attempt to restart
every 100 ms until the OVP condition is removed.
Safety Requirements
The converters meet North American and International
safety regulatory requirements per UL60950 and EN60950.
Basic Insulation is provided between input and output.
To comply with safety agencies requirements, an input line
fuse must be used external to the converter. A 3-A fuse is
recommended for use with this product.
Electromagnetic Compatibility (EMC)
EMC requirements must be met at the end-product system
level, as no specific standards dedicated to EMC character-
istics of board mounted component dc-dc converters exist.
However, Power-One tests its converters to several system
level standards, primary of which is the more stringent
EN55022, Information technology equipment - Radio distur-
bance characteristics - Limits and methods of measurement.
With the addition of a simple external filter (see application
notes), all versions of the Q48T30 converters pass the re-
quirements of Class B conducted emissions per EN55022
and FCC, and meet at a minimum, Class A radiated emis-
sions per EN 55022 and Class B per FCC Title 47CFR, Part
15-J. Please contact Power-One Applications Engineering
for details of this testing.
Input Transient Withstand
This family of converters meets the input transient withstand
requirements of Bellcore GR-513 (Section 13, Table 4.2) as
shown in Fig. 6, and also withstands 100 V input transient for
100 ms.
Transient Duration
Vdc
Overtemperature Protection (OTP)
5 seconds
10 ms
-65
-75
The converter will shut down under an overtemperature con-
dition to protect itself from overheating caused by operation
outside the thermal derating curves, or operation in abnor-
mal conditions such as system fan failure. After the con-
verter has cooled to a safe operating temperature, it will
automatically restart.
10 μ s -100
1 μ s -200
Fig. 6: Input transient withstand capability per Bellcore GR-513.
(Negative signs imply telecom transients relative to Vin(+) terminal)
JUN 02, 2003 revised to NOV 20, 2006
Page 7 of 14
www.power-one.com
相关PDF资料 |
PDF描述 |
|---|---|
| Q48T30025-NDB0 | DC/DC QTR BRICK 75W 2.5V T/H |
| Q48T30033-NAAC | DC/DC QTR BRICK 100W 3.3V T/H |
| QAK2J335KTP | CAP FILM 3.3UF 630VDC AXIAL |
| QD48S018033-NS00 | DC/DC QTR BRICK 77W 1.8/3.3V |
| QD48T012025-NCB0 | DC/DC QTR BRICK DL 1.2/2.5V T/H |
相关代理商/技术参数 |
参数描述 |
|---|---|
| Q48T30018-NBA0G | 功能描述:DC/DC转换器 RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| Q48T30018-NBAP | 制造商:Power-One 功能描述:DC/DC PS SGL-OUT 1.8V 30A 8PIN QUARTER-BRICK - Bulk |
| Q48T30018-NBAPG | 制造商:Power-One 功能描述:DC/DC PS SGL-OUT 1.8V 30A - Bulk |
| Q48T30018-NBB0 | 功能描述:DC/DC转换器 48V IN 1.8V OUT 54W RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| Q48T30018-NBB0G | 功能描述:DC/DC转换器 36-75Vin 30A 1.8Vout 75W RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
发布紧急采购，3分钟左右您将得到回复。