- 您现在的位置：买卖IC网 > Datasheet目录874 > QM48S40033-NS00 (Power-One)DC/DC QTR BRICK 132W 3.3V SMD Datasheet资料下载
参数资料
| 型号： | QM48S40033-NS00 |
| 厂商： | Power-One |
| 文件页数： | 7/13页 |
| 文件大小： | 0K |
| 描述： | DC/DC QTR BRICK 132W 3.3V SMD |
| 标准包装： | 125 |
| 系列： | * |
QM48S40033 DC-DC Converter Data Sheet
36-75 VDC Input; 3.3 VDC @ 40A Output
Characterization
General Information
The converter has been characterized for many operational
aspects, to include thermal derating (maximum load current
as a function of ambient temperature and airflow) for vertical
and horizontal mounting, efficiency, start-up and shutdown
parameters, output ripple and noise, transient response to
load step-change, overload and short circuit.
The following pages contain specific plots or waveforms as-
sociated with the converter. Additional comments for specific
data are provided below.
Test Conditions
All data presented were taken with the converter soldered to
a test board, specifically a 0.060” thick printed wiring board
(PWB) with four layers. The top and bottom layers were not
metalized. The two inner layers, comprising two-ounce cop-
per, were used to provide traces for connectivity to the con-
verter.
The lack of metalization on the outer layers as well as the
limited thermal connection ensured that heat transfer from
the converter to the PWB was minimized. This provides a
worst-case but consistent scenario for thermal derating pur-
poses.
All measurements requiring airflow were made in Power-
One’s vertical and horizontal wind tunnel facilities using In-
frared (IR) thermography and thermocouples for thermome-
try.
Ensuring components on the converter do not exceed their
ratings is important to maintaining high reliability. If one an-
ticipates operating the converter at or close to the maximum
loads specified in the derating curves, it is prudent to check
actual operating temperatures in the application. Thermo-
graphic imaging is preferable; if this capability is not avail-
able, then thermocouples may be used. Power-One recom-
mends the use of AWG #40 gauge thermocouples to ensure
measurement accuracy. Careful routing of the thermocouple
leads will further minimize measurement error. Refer to Fig-
ure H for optimum measuring thermocouple location.
Thermal Derating
Load current vs. ambient temperature and airflow rates are
given in Figs. 1 and 2 for vertical and horizontal converter
mounting. Ambient temperature was varied between 25°C
and 85°C, with airflow rates from 30 to 500 LFM (0.15 to 2.5
m/s).
For each set of conditions, the maximum load current was
defined as the lowest of:
(i) The output current at which any FET junction temperature
does not exceed a maximum specified temperature (120°C)
as indicated by the thermographic image, or
(ii) The nominal rating of the converter (40 A).
During normal operation, derating curves with maximum FET
temperature less than or equal to 120°C should not be ex-
ceeded. Temperature on the PCB at the thermocouple loca-
tion shown in Fig. H should not exceed 118°C in order to
operate inside the derating curves.
Efficiency
Fig. 3 shows the efficiency vs. load current plot for ambient
temperature of 25oC, airflow rate of 300 LFM (1.5 m/s) with
vertical mounting and input voltages of 36 V, 48 V and 72 V.
Also, a plot of efficiency vs. load current, as a function of
ambient temperature with Vin = 48 V, airflow rate of 200 LFM
(1 m/s) with vertical mounting is shown in Fig. 4.
Power Dissipation
Fig. 5 shows the power dissipation vs. load current plot for
Ta = 25oC, airflow rate of 300 LFM (1.5 m/s) with vertical
mounting and input voltages of 36 V, 48 V and 72 V. Also, a
plot of power dissipation vs. load current, as a function of
ambient temperature with Vin = 48 V, airflow rate of 200 LFM
(1 m/s) with vertical mounting is shown in Fig. 6.
Start-up
Output voltage waveforms, during the turn-on transient using
the ON/OFF pin for full rated load currents (resistive load)
are shown without and with external load capacitance in
Fig. 7 and Fig. 8, respectively.
Ripple and Noise
Fig. 10 shows the output voltage ripple waveform, measured
at full rated load current with a 10 μ F tantalum and 1 μ F ce-
ramic capacitor across the output. Note that all output volt-
age waveforms are measured across a 1 μ F ceramic capaci-
tor.
The input reflected ripple current waveforms are obtained
using the test setup shown in Fig. 11. The corresponding
waveforms are shown in Fig. 12 and Fig. 13.
FEB 10, 2004 revised to NOV 13, 2006
Page 7 of 13
www.power-one.com
相关PDF资料 |
PDF描述 |
|---|---|
| QM48T25050-NDA0 | DC/DC QTR BRICK 125W 5V T/H |
| QM48T45010-NAAP | DC/DC QTR BRICK 45W 1V T/H |
| QME48T20120-NGA0 | DC/DC QUARTER BRICK 12V OUT |
| QME48T40050-NGA0 | DC/DC QUARTER BRICK 5V OUT |
| QMS07DH | 19" RACK FOR 3X 48V FRONT END |
相关代理商/技术参数 |
参数描述 |
|---|---|
| QM48S40033-NS00A | 制造商:Power-One 功能描述: |
| QM48S40033-NS00G | 功能描述:DC/DC转换器 RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| QM48S40033-NS0P | 制造商:Power-One 功能描述:DC/DC PS SGL-OUT 3.3V 40A 132W 8PIN QUARTER-BRICK - Bulk |
| QM48S40033-NS0PG | 制造商:Power-One 功能描述:DC/DC PS SGL-OUT 3.3V 40A 132W 8PIN QUARTER-BRICK - Bulk |
| QM48S40033-PS00 | 制造商:Power-One 功能描述:DC/DC PS SGL-OUT 3.3V 40A 132W - Bulk |
发布紧急采购，3分钟左右您将得到回复。