- 您现在的位置：买卖IC网 > Datasheet目录875 > QM48T45010-NAAP (Power-One)DC/DC QTR BRICK 45W 1V T/H Datasheet资料下载
参数资料
| 型号： | QM48T45010-NAAP |
| 厂商： | Power-One |
| 文件页数： | 3/36页 |
| 文件大小： | 0K |
| 描述： | DC/DC QTR BRICK 45W 1V T/H |
| 标准包装： | 250 |
| 系列： | * |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
QM48T45 Family DC-DC Converter Data Sheet
36-75 VDC Input; 1.0-3.3 VDC @ 45 A Output
Operations
Input and Output Impedance
These power converters have been designed to be
stable with no external capacitors when used in low
inductance input and output circuits.
In many applications, the inductance associated with
the distribution from the power source to the input of
the converter can affect the stability of the converter.
The addition of a 33 μF electrolytic capacitor with an
ESR < 1 ? across the input helps to ensure stability
of the converter. In many applications, the user has
to use decoupling capacitance at the load. The
power converter will exhibit stable operation with
external load capacitance up to 40,000 μF on
of ≤ 0.8 V. An external voltage source ( ± 20 V
maximum) may be connected directly to the ON/OFF
input, in which case it must be capable of sourcing or
sinking up to 1 mA depending on the signal polarity.
See the Startup Information section for system timing
waveforms associated with use of the ON/OFF pin.
Remote Sense (Pins 5 and 7)
The remote sense feature of the converter
compensates for voltage drops occurring between the
output pins of the converter and the load. The
SENSE(-) (Pin 5) and SENSE(+) (Pin 7) pins should
be connected at the load or at the point where
regulation is required (see Fig. B).
QmaX
Series
3.3-1.0 V outputs.
Additionally, see the EMC section of this data sheet
Vin (+)
TM
Converter
(Top View)
Vout (+)
100
SENSE(+)
Rw
for discussion of other external components which
may be required for control of conducted emissions.
Vin
ON/ OFF
Vin(-)
TRIM
SENSE(-)
10
Vout(-)
Rw
Rload
ON/OFF (Pin 2)
The ON/OFF pin is used to turn the power converter
on or off remotely via a system signal. There are two
remote control options available, positive logic and
negative logic, with both referenced to Vin(-). A
typical connection is shown in Fig. A.
Fig. B: Remote sense circuit configuration.
CAUTION
If remote sensing is not utilized, the SENSE(-) pin must be
connected to the Vout(-) pin (Pin 4), and the SENSE(+) pin must
be connected to the Vout(+) pin (Pin 8) to ensure the converter will
QmaX
Series
Vin (+)
TM
Converter
(Top View)
Vout (+)
SENSE (+)
regulate at the specified output voltage. If these connections are not
made, the converter will deliver an output voltage that is slightly
higher than the specified data sheet value.
Vin
CONTROL
ON/ OFF
Vin (-)
TRIM
SENSE (-)
Vout (-)
Rload
Because the sense leads carry minimal current, large
traces on the end-user board are not required.
However, sense traces should be run side by side and
INPUT
Fig. A: Circuit configuration for ON/OFF function.
The positive logic version turns on when the ON/OFF
pin is at a logic high and turns off when at a logic low.
The converter is on when the ON/OFF pin is left
open. See the Electrical Specifications for logic
high/low definitions.
The negative logic version turns on when the pin is at
a logic low and turns off when the pin is at a logic
high. The ON/OFF pin can be hardwired directly to
Vin(-) to enable automatic power up of the converter
without the need of an external control signal
The ON/OFF pin is internally pulled up to 5 V through
a resistor. A properly debounced mechanical switch,
open-collector transistor, or FET can be used to drive
the input of the ON/OFF pin. The device must be
capable of sinking up to 0.2 mA at a low level voltage
located close to a ground plane to minimize system
noise and ensure optimum performance.
The converter’s output overvoltage protection (OVP)
senses the voltage across Vout(+) and Vout(-), and
not across the sense lines, so the resistance (and
resulting voltage drop) between the output pins of the
converter and the load should be minimized to
prevent unwanted triggering of the OVP.
When utilizing the remote sense feature, care must be
taken not to exceed the maximum allowable output
power capability of the converter, which is equal to the
product of the nominal output voltage and the
allowable output current for the given conditions.
When using remote sense, the output voltage at the
converter can be increased by as much as 10%
above the nominal rating in order to maintain the
required voltage across the load. Therefore, the
designer must, if necessary, decrease the maximum
MCD10073 Rev. 1.0
Page 3 of 36
www.power-one.com
相关PDF资料 |
PDF描述 |
|---|---|
| QME48T20120-NGA0 | DC/DC QUARTER BRICK 12V OUT |
| QME48T40050-NGA0 | DC/DC QUARTER BRICK 5V OUT |
| QMS07DH | 19" RACK FOR 3X 48V FRONT END |
| QXK2E106KTP | CAP FILM 10UF 250VDC RADIAL |
| QXK2J474KTPTZH | CAP FILM 0.47UF 630VDC RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| QM48T45010-NAAPG | 制造商:Power-One 功能描述:DCDC,HAZMAT - Bulk |
| QM48T45010-NAB0G | 制造商:Power-One 功能描述:DCDC,HAZMAT - Bulk |
| QM48T45010-NABPG | 制造商:Power-One 功能描述:DCDC,HAZMAT - Bulk |
| QM48T45010-NAC0G | 制造商:Power-One 功能描述:DCDC,HAZMAT - Bulk |
| QM48T45010-NACP | 功能描述:DC/DC QTR BRICK 45W 1V T/H RoHS:是 类别:电源 - 板载 >> DC DC Converters 系列:* 标准包装:5 系列:* |
发布紧急采购，3分钟左右您将得到回复。