- 您现在的位置：买卖IC网 > PDF目录299801 > QPI-6-EVAL1 (Vicor Corporation) Evaluation Board for Active EMI Filters PDF资料下载
参数资料
| 型号： | QPI-6-EVAL1 |
| 厂商： | Vicor Corporation |
| 元件分类： | DC/DC变换器 |
| 英文描述： | Evaluation Board for Active EMI Filters |
| 中文描述： | 评估板有源EMI滤波器 |
| 文件页数： | 1/2页 |
| 文件大小： | 126K |
| 代理商： | QPI-6-EVAL1 |
Picor Corporation www.picorpower.com
QPI-X-EVAL1 Data Sheet Rev. 1.2 Page 1 of 2
The QPI-X-EVAL1 is an easy to use evaluation
board for testing the QPI family of active EMI
filters. The evaluation board includes a mounted
QPI, capacitors, optional RY resistor and screw
terminals for electrical connections.
When using the evaluation board, pay special
attention to wiring and grounding. Wires should be
kept as short as possible and positioned to minimize
radiated pick up around the QPI. Refer to Figure 1
below and the QPI-AN1 application note for the
proper measurement set up.
Figure 2 shows the schematic of the QPI-X-EVAL1.
Note that resistor RY is included with the evaluation
board for use with non-resonant mode converters. To
ensure the best results, make sure that the QPI shield
connection is as close as possible to the common point
of the bypass Y-capacitors and shield plane under the
converters on the system board.
BUS+
QPI+
BUS-
QPI-
SHIELD
BUS
SUPPLY
QPI
VIN+
VOUT+
VIN-
VOUT-
CONVERTER
Optional GND
Connection
C1
C2
C3
C4
RY
CIN
LISN
LISN Ground Plane
Figure 1 - Spectrum Analyzer Test Setup for the evaluation board (QPI and Converter 5mm above LISN Ground Plane)
Figure 3 shows the component locations on the EVAL
board PCB.
Filter performance in the application is highly
dependent on several factors and cannot be
extrapolated from insertion loss curves alone. Final
noise performance is a complex function of filter
elements, equipment grounding and noise source
impedances, which vary in magnitude and phase over
the frequency spectrum of interest.
Designers should be aware that to select and qualify
an EMI filter for conducted noise, they must test the
filter in their product under the set up and conditions
specified in the applicable EMI standards. Measurements
should be made in consultation with in-house
compliance testing or an independent EMI test facility.
Check www.picorpower.com for data sheets,
application notes and additional product information.
QPI-X-EVAL1
QuietPower
Evaluation Board for Active EMI Filters
相关PDF资料 |
PDF描述 |
|---|---|
| QPO-1L | Output Ripple Attenuation SiP |
| QPO-1Q | Output Ripple Attenuation SiP |
| QPO-2EVAL1 | Evaluation Board for QPO-2 Active Output Filter |
| QPO-2L | QPO-2L Low Voltage Output Ripple Attenuator |
| QS54FCT2240ATZB | FCT SERIES, DUAL 4-BIT DRIVER, INVERTED OUTPUT, PZIP20 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| QPI-6L | 制造商:VICOR 制造商全称:Vicor Corporation 功能描述:14 Amp Active EMI Filter for 48V DC Bus |
| QPI-6LZ | 功能描述:FILTER 48V, 14A ACTIVE EMI RoHS:是 类别:集成电路 (IC) >> 接口 - 滤波器 - 有源 系列:Picor®, QUIETPOWER® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1,000 系列:- 滤波器类型:连续时间，带通低通 频率 - 截止或中心:150kHz 滤波器数:4 滤波器阶数:8th 电源电压:4.74 V ~ 11 V，±2.37 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) |
| QPI-6LZ-01 | 功能描述:IC INTERFACE FILTER RoHS:是 类别:集成电路 (IC) >> 接口 - 滤波器 - 有源 系列:Picor®, QUIETPOWER® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1,000 系列:- 滤波器类型:连续时间，带通低通 频率 - 截止或中心:150kHz 滤波器数:4 滤波器阶数:8th 电源电压:4.74 V ~ 11 V，±2.37 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) |
| QPI-7-CB1 | 制造商:Vicor Corporation 功能描述:QPI-7LZ DOSA STYLE EVALUATION BOARD |
| QPI-7-EVAL1 | 制造商:Vicor Corporation 功能描述:QPI-7LZ Universal Evaluation Board for 6 A 24 V Active EMI Filter w/ Hot-Swap |
发布紧急采购，3分钟左右您将得到回复。