参数资料
| 型号： | QT60168C-ASG |
| 厂商： | Atmel |
| 文件页数： | 10/28页 |
| 文件大小： | 0K |
| 描述： | IC TOUCH SENSOR 16KEY 32TQFP |
| 标准包装： | 250 |
| 系列： | QMatrix™, QProx™ |
| 类型： | 电容性 |
| 输入数/键： | 16 键 |
| 分辨率（位）： | 9，11 b |
| 评估套件： | 可供 |
| 数据接口： | 串行，SPI? |
| 电源电压： | 3 V ~ 5 V |
| 电流 - 电源： | 25mA |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-TQFP |
| 供应商设备封装： | 32-TQFP（7x7） |
| 包装： | 托盘 |
| 配用： | 427-1087-ND - BOARD EVAL QT60248-AS QMATRIX |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
5 Setups
The devices calibrate and process all signals using a
number of algorithms specifically designed to provide for
high survivability in the face of adverse environmental
challenges. They provide a large number of processing
options which can be user-selected to implement very
flexible, robust keypanel solutions.
User-defined Setups are employed to alter these algorithms
to suit each application. These setups are loaded into the
device in a block load over the serial interface. The Setups
are stored in an onboard eeprom array. After a setups block
load, the device should be reset to allow the new Setups
parameters to take effect. This reset can be either a
hardware or software reset.
Refer to Table 5.1, page 22 for a table of all Setups.
Block length issues: The setups block is 100 bytes long to
accommodate 24 keys. This can be a burden on smaller host
controllers with limited memory. In larger quantities the
devices can be procured with the setups block
preprogrammed from Quantum. If the application only
requires a small number of keys (such as 16) then the
setups table can be compressed in the host by filling large
stretches of the Setups area with nulls.
Many setups employ lookup-table value translation. The
Setups Block Summary on page 23 shows all translation
values.
Default Values shown are factory defaults.
5.1 Negative Threshold - NTHR
The negative threshold value is established relative to a
key’s signal reference value. The threshold is used to
determine key touch when crossed by a negative-going
signal swing after having been filtered by the detection
integrator. Larger absolute values of threshold desensitize
keys since the signal must travel farther in order to cross the
threshold level. Conversely, lower thresholds make keys
more sensitive.
As Cx and Cs drift, the reference point drift-compensates for
these changes at a user-settable rate; the threshold level is
recomputed whenever the reference point moves, and thus it
also is drift compensated.
The amount of NTHR required depends on the amount of
signal swing that occurs when a key is touched. Thicker
panels or smaller key geometries reduce ‘key gain’, ie signal
swing from touch, thus requiring smaller NTHR values to
detect touch.
The negative threshold is programmed on a
per-key basis using the Setup process. See table,
page 23.
Negative hysteresis: NHYST is fixed at 12.5% of
the negative threshold value and cannot be
altered
.
Typical values:
3 to 8
(7 to 12 counts of threshold; 4 is internally
added to NTHR to generate the threshold).
Default value:
6
(10 counts of threshold)
5.2 Positive Threshold - PTHR
The positive threshold is used to provide a mechanism for
recalibration of the reference point when a key's signal
moves abruptly to the positive. This condition is not normal,
and usually occurs only after a recalibration when an object
is touching the key and is subsequently removed. The desire
is normally to recover from these events quickly.
Positive hysteresis: PHYST is fixed at 12.5% of the positive
threshold value and cannot be altered.
Positive threshold levels are all fixed at 6 counts of signal
and cannot be modified.
5.3 Drift Compensation - NDRIFT, PDRIFT
Signals can drift because of changes in Cx and Cs over time
and temperature. It is crucial that such drift be compensated,
else false detections and sensitivity shifts can occur.
Drift compensation (Figure 5-1) is performed by making the
reference level track the raw signal at a slow rate, but only
while there is no detection in effect. The rate of adjustment
must be performed slowly, otherwise legitimate detections
could be ignored. The devices drift compensate using a
slew-rate limited change to the reference level; the threshold
and hysteresis values are slaved to this reference.
When a finger is sensed, the signal falls since the human
body acts to absorb charge from the cross-coupling between
X and Y lines. An isolated, untouched foreign object (a coin,
or a water film) will cause the signal to rise very slightly due
to an enhancement of coupling. This is contrary to the way
most capacitive sensors operate.
Once a finger is sensed, the drift compensation mechanism
ceases since the signal is legitimately detecting an object.
Drift compensation only works when the signal in question
has not crossed the negative threshold level.
The drift compensation mechanism can be asymmetric; the
drift-compensation can be made to occur in one direction
faster than it does in the other simply by changing the
NDRIFT Setup parameter. This can be done on a per-key
basis.
The PDRIFT parameter is fixed at 0.4 seconds per count of
reference drift.
Specifically, drift compensation should be set to compensate
faster for increasing signals than for decreasing signals.
Decreasing signals should not be compensated quickly,
since an approaching finger could be compensated for
partially or entirely before even touching the touch pad.
lQ
18
QT60248-AS R4.02/0405
Figure 5-1 Thresholds and Drift Compensation
Threshold
Signal
Hysteresis
Reference
Output
相关PDF资料 |
PDF描述 |
|---|---|
| SY100EL16VBZI TR | IC RCVR DIFF 5V/3.3V 8-SOIC |
| D38999/24WG41SC | CONN RCPT 41POS JAM NUT W/SCKT |
| MS3100E28-10P | CONN RCPT 7POS WALL MNT W/PINS |
| MS3126E20-41PY | CONN PLUG 41POS STRAIGHT W/PINS |
| MS3126E20-41PW | CONN PLUG 41POS STRAIGHT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| QT60168C-ASG-SL683 | 功能描述:接口 - 专用 Integrated Circuit RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| QT60240 | 制造商:QUANTUM 制造商全称:QUANTUM 功能描述:16 AND 24 KEY QMATRIX TOUCH SENSOR ICs |
| QT60240-ASG | 制造商:Quantum Corp 功能描述:QPROX SENSOR 24 KEYS SMD MLF-32 |
| QT60240-ATG | 功能描述:接口 - 专用 Integrated Circuit RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| QT60240-ATG SL924 | 制造商:Atmel Corporation 功能描述:INTEGRATED-CIRCUIT 制造商:Atmel 功能描述:INTEGRATED-CIRCUIT |
发布紧急采购，3分钟左右您将得到回复。