- 您现在的位置：买卖IC网 > PDF目录69320 > RA-8581SAB-3 (EPSON TOYOCOM CORP) REAL TIME CLOCK, PDSO14 PDF资料下载
参数资料
| 型号： | RA-8581SAB-3 |
| 厂商： | EPSON TOYOCOM CORP |
| 元件分类： | 时钟/数据恢复及定时提取 |
| 英文描述： | REAL TIME CLOCK, PDSO14 |
| 封装： | SOP-14 |
| 文件页数： | 25/32页 |
| 文件大小： | 569K |
| 代理商： | RA-8581SAB-3 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页当前第25页第26页第27页第28页第29页第30页第31页第32页
RA – 8581 SA
Page - 28
MQ 432 - 01
11. Application notes
1) Notes on handling
This module uses a C-MOS IC to realize low power consumption. Carefully note the following cautions when handling.
(1) Static electricity
While this module has built-in circuitry designed to protect it against electrostatic discharge, the chip could still be damaged by a
large discharge of static electricity. Containers used for packing and transport should be constructed of conductive materials. In
addition, only soldering irons, measurement circuits, and other such devices which do not leak high voltage should be used with
this module, which should also be grounded when such devices are being used.
(2) Noise
If a signal with excessive external noise is applied to the power supply or input pins, the device may malfunction or "latch up." In
order to ensure stable operation, connect a filter capacitor (preferably ceramic) of greater that 0.1F as close as possible to the
power supply pins (between VDD and GNDs). Also, avoid placing any device that generates high level of electronic noise near
this module.
* Do not connect signal lines to the shaded area in the figure shown in Fig. 1 and, if possible, embed this area in a GND land.
(3) Voltage levels of input pins
When the input pins are at the mid-level, this will cause increased current consumption and a reduced noise margin, and can
impair the functioning of the device. Therefore, try as much as possible to apply the voltage level close to VDD or GND.
(4) Handling of unused pins
Since the input impedance of the input pins is extremely high, operating the device with these pins in the open circuit state can
lead to unstable voltage level and malfunctions due to noise. Therefore, pull-up or pull-down resistors should be provided for all
unused input pins.
2) Notes on packaging
(1) Soldering heat resistance.
If the temperature within the package exceeds +260 °C, the characteristics of the crystal oscillator will be degraded and it may
be damaged. The reflow conditions within our reflow profile is recommended. Therefore, always check the mounting
temperature and time before mounting this device. Also, check again if the mounting conditions are later changed.
* See Fig. 2 profile for our evaluation of Soldering heat resistance for reference.
(2) Mounting equipment
While this module can be used with general-purpose mounting equipment, the internal crystal oscillator may be damaged in
some circumstances, depending on the equipment and conditions. Therefore, be sure to check this. In addition, if the mounting
conditions are later changed, the same check should be performed again.
(3) Ultrasonic cleaning
Depending on the usage conditions, there is a possibility that the crystal oscillator will be damaged by resonance during
ultrasonic cleaning. Since the conditions under which ultrasonic cleaning is carried out (the type of cleaner, power level, time,
state of the inside of the cleaning vessel, etc.) vary widely, this device is not warranted against damage during ultrasonic
cleaning.
(4) Mounting orientation
This device can be damaged if it is mounted in the wrong orientation. Always confirm the orientation of the device before
mounting.
(5) Leakage between pins
Leakage between pins may occur if the power is turned on while the device has condensation or dirt on it. Make sure the device
is dry and clean before supplying power to it.
Fig. 1 : Example GND Pattern
Fig. 2 : Reference profile for our evaluation of Soldering heat resistance.
RA
– 8581 SA
(SOP - 14pin)
+1 ~ +5 °C / s
100 s
Pre-heating area
1 ~ -5 °C / s
time [ s ]
Temperature [°C ]
+170 °C
+220 °C
+260 °C Max.
+1 ~ +5 °C / s
35 s
Stable Melting area
* In addition, please confirm the Notes of an individual specification.
相关PDF资料 |
PDF描述 |
|---|---|
| RB80526PY733256 | 32-BIT, 733 MHz, MICROPROCESSOR, CPGA370 |
| RB80526PY533256 | 32-BIT, 533 MHz, MICROPROCESSOR, CPGA370 |
| RB80526PY600256 | 32-BIT, 600 MHz, MICROPROCESSOR, CPGA370 |
| RB80526PY800256 | 32-BIT, 800 MHz, MICROPROCESSOR, CPGA370 |
| RB80526PY933256 | 32-BIT, 933 MHz, MICROPROCESSOR, CPGA370 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| RA863 | 制造商:Thomas & Betts 功能描述:TERMINAL RING TONGUE #8 CRIMP RED 制造商:Thomas & Betts 功能描述:TERMINAL, RING TONGUE, #8, CRIMP, RED 制造商:Thomas & Betts 功能描述:TERMINAL, RING TONGUE, #8, CRIMP, RED; Connector Type:Ring Tongue; Series:Sta-Kon; Insulator Color:Red; Termination Method:Crimp; Stud/Tab Size:#8; Wire Size AWG Min:22AWG; Wire Size AWG Max:16AWG; Contact Material:Copper ;RoHS Compliant: Yes 制造商:Thomas & Betts 功能描述:Ring Tongue Terminal 16-22AWG 21.08mm 6.6mm Electro-Tin Bulk |
| RA863M | 制造商:Thomas & Betts 功能描述:TERMINAL BELT ASSY |
| RA863U | 制造商:Thomas & Betts 功能描述:NYLON RING TERM 22-18 #8 BOLT 90DEG |
| RA863UFR | 制造商:Thomas & Betts 功能描述:NYLON RING 22-18 #8 BOLT 45 DEG REV |
| RA867 | 制造商:Thomas & Betts 功能描述:TERMINAL RING TONGUE #8 CRIMP RED 制造商:Thomas & Betts 功能描述:TERMINAL, RING TONGUE, #8, CRIMP, RED 制造商:Thomas & Betts 功能描述:TERMINAL, RING TONGUE, #8, CRIMP, RED; Connector Type:Ring Tongue; Series:RA; Insulator Color:Red; Termination Method:Crimp; Stud/Tab Size:#8; Wire Size AWG Min:22AWG; Wire Size AWG Max:16AWG; Contact Material:Copper; Stud Size:#8 ;RoHS Compliant: Yes 制造商:Thomas & Betts 功能描述:Ring Tongue Terminal 16-22AWG 24.63mm 7.87mm Electro-Tin Bulk |
发布紧急采购，3分钟左右您将得到回复。