- 您现在的位置：买卖IC网 > PDF目录299865 > RC2951M-3.3 (FAIRCHILD SEMICONDUCTOR CORP) FIXED/ADJUSTABLE POSITIVE LDO REGULATOR, 0.7 V DROPOUT, PDSO8 PDF资料下载
参数资料
| 型号： | RC2951M-3.3 |
| 厂商： | FAIRCHILD SEMICONDUCTOR CORP |
| 元件分类： | 固定／可调正电压单路输出LDO稳压器 |
| 英文描述： | FIXED/ADJUSTABLE POSITIVE LDO REGULATOR, 0.7 V DROPOUT, PDSO8 |
| 封装： | SOIC-8 |
| 文件页数： | 7/11页 |
| 文件大小： | 213K |
| 代理商： | RC2951M-3.3 |
PRODUCT SPECIFICATION
RC2951
REV. 1.0.0 2/8/01
5
Applications Discussion
The RC2951 regulator is designed with internal current lim-
iting and thermal shutdown. It is not internally compensated
and requires a 1.0F (or greater) capacitor between the out-
put terminal and ground for stability. At lower output volt-
ages, more capacitance is required (2.2F or more is
recommended for 3V and 3.3V versions) for stability. Most
types of aluminum, tantalum or multilayer ceramic capaci-
tors will perform adequately. Solid tantalums or appropriate
multilayer ceramic capacitors are suggested for operation
below 25°C. At lower values of output current, less capaci-
tance is needed to maintain stability at output. The capacitor
at the output can be reduced to 0.33F for currents less that
10mA, or 0.1F for currents below 1.0mA.
Using the adjustable versions at voltages below 5V runs the
error amplier at lower gains so that more output capaci-
tance is needed. For the worst-case situation of a 100 mA
load at 1.23V output (Output shorted to Feedback) a
3.3
F (or greater) capacitor should be used.
When setting the output voltage of the RC2951 versions with
external resistors, a minimum load of 1
A is recommended.
A 1
F tantalum or aluminum electrolytic capacitor should
be placed from the RC2951 input to ground if there is more
than 10 inches of wire between the input and the AC lter
capacitor or if a battery is used as the input.
Stray capacitance to the RC2951 Feedback terminal can
cause instability. This may especially be a problem when
using high value external resistors to set the output voltage.
Adding a 100 pF capacitor between Output and Feedback
and increasing the output capacitor to at least 3.3
F will x
this problem.
Error Detection Comparator Output
The comparator switches to a logic low whenever the
RC2951 output falls out of regulation by more than approxi-
mately 5%. This value is the comparator’s built-in offset of
about 60 mV divided by the 1.235 internal reference voltage.
This trip level remains “5% below normal” regardless of the
value of the output voltage. For example, the error ag trip
level is typically 4.75V for a 5V output or 11.4V for a 12V
output. The out of regulation condition may be due either to
low input voltage, current limiting, or thermal limiting.
Figure 1 is a timing diagram showing the ERROR signal and
the regulated output voltage as the RC2951 input is ramped
up and down. For 5V versions, the ERROR signal becomes
valid (low) at about 1.3V input. It goes high at about 5V
input (the input voltage at which VOUT = 4.75.) Since the
RC2951’s dropout voltage is load-dependent (see curve in
typical performance characteristics), the input voltage trip
point (about 5V) will vary with the load current. The output
voltage trip point (approx. 4.75V) does not vary with load.
Figure 1. ERROR Output Timing
The error comparator has an open-collector output which
requires an external pullup resistor. This resistor may be
returned to the output or some other supply voltage depend-
ing on system requirements. In determining a value for this
resistor, note that while the output is rated to sink 400
A,
this sink current adds to battery drain in a low battery condi-
tion. Suggested values range from 100k to 1M
. The resistor
is not required if this output is unused.
Programming the Output Voltage (RC2951)
The RC2951 may be pin-strapped for the nominal xed
output voltage using its internal voltage divider by tying the
output and sense pins together, and also tying the feedback
and VTAP pins together. Alternatively, it may be programmed
for any output voltage between its 1.235V reference and its
30V maximum rating. As seen in Figure 2 an external pair of
resistors is required.
Output
Voltage
Input
Voltage
5V
1.3V
4.75V
2950-10
Error*
相关PDF资料 |
PDF描述 |
|---|---|
| RC2951M | FIXED/ADJUSTABLE POSITIVE LDO REGULATOR, 0.7 V DROPOUT, PDSO8 |
| RC5503 | UHF Controller |
| RC5504 | UHF Controller |
| RC5505 | UHF Controller |
| RC5506 | UHF Controller |
相关代理商/技术参数 |
参数描述 |
|---|---|
| RC2951M33_32 | 功能描述:上下转换器 RoHS:否 制造商:Texas Instruments 产品:Down Converters 射频:52 MHz to 78 MHz 中频:300 MHz LO频率: 功率增益: P1dB: 工作电源电压:1.8 V, 3.3 V 工作电源电流:120 mA 最大功率耗散:1 W 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PQFP-128 |
| RC2951MT | 功能描述:低压差稳压器 - LDO RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| RC2A-12DS | 制造商:World Products 功能描述: |
| RC2A-12DSF | 制造商:World Products 功能描述: |
| RC2A-24DSF | 制造商:World Products 功能描述: |
发布紧急采购，3分钟左右您将得到回复。